Nissan Rogue (T33) 2021-Present Service Manual: It Can Communication 2 Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Electrical & Power Control :: Lan System / Can :: Dtc/circuit Diagnosis / It Can Communication 2 Circuit

Diagnosis Procedure

CHECK NETWORK DIAGNOSIS

Check the "Network diagnosis" results from CONSULT to see that the diagnostic CAN communication circuit have no malfunction.

Are the diagnostic CAN communication circuit normal?

YES>>

GO TO 2.

NO>>

Check and repair diagnostic CAN communication circuit.

CONNECTOR INSPECTION

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect all the unit connectors on IT CAN communication 2 circuit.

  4. Check terminals and connectors for damage, bend and loose connection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the connector of 8CH CAN gateway.

  2. Check the continuity between the 8CH CAN gateway harness connector terminals.

    8CH CAN gateway harness connector Continuity
    Connector No. Terminal No.
    M45 27 15 Existed
    28 16 Existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Check the harness and repair or replace the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the 8CH CAN gateway harness connector terminals.

8CH CAN gateway harness connector Continuity
Connector No. Terminal No.
M45 27 28 Not existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Check the harness and repair the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the 8CH CAN gateway and the ground.

8CH CAN gateway harness connector Ground Continuity
Connector No. Terminal No.
M45 27 Not existed
28 Not existed

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Check the harness and repair the root cause.

CHECK 8CH CAN GATEWAY TERMINATION CIRCUIT

  1. Remove the 8CH CAN gateway.

  2. Check the resistance between the 8CH CAN gateway terminals.

    8CH CAN gateway Resistance (Ω)
    Terminal No.
    27 28 Approx. 108 – 132
    15 16 Approx. 108 – 132

Is the measurement value within the specification?

YES>>

GO TO 7.

NO>>

Replace the 8CH CAN gateway.

CHECK SYMPTOM

Connect all the connectors. Check if the symptoms described in the “Symptom (Results from interview with customer)” are reproduced.

Inspection result

Reproduced>>

GO TO 8.

Non-reproduced>>

Start the diagnosis again. Follow the trouble diagnosis procedure when past error is detected.

CHECK UNIT REPRODUCTION

Perform the reproduction test as per the following procedure for each unit.

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect one of the unit connectors of IT CAN communication 2 circuit.

    NOTE:

    8CH CAN gateway has two termination circuits. Check other units first.

  4. Connect the battery cable to the negative terminal. Check if the symptoms described in the “Symptom (Results from interview with customer)” are reproduced.

    NOTE:

    Although unit-related error symptoms occur, do not confuse them with other symptoms.

Inspection result

Reproduced>>

Connect the connector. Check other units as per the above procedure.

Non-reproduced>>

Replace the unit whose connector was disconnected.

    It Can Communication 1 Circuit
    Diagnosis Procedure CHECK NETWORK DIAGNOSIS Check the "Network diagnosis" results from CONSULT to see that the diagnostic CAN communication circuit have no malfunction. Are the ...
    It Can Communication 3 Circuit
    Diagnosis Procedure CHECK NETWORK DIAGNOSIS Check the "Network diagnosis" results from CONSULT to see that the diagnostic CAN communication circuit have no malfunction. Are the ...

    Other materials:

    Lane Change Assist
    Basic information Lane Change Assist is a feature of ProPILOT Assist 2.1 on the Nissan Rogue. Read the entire ProPILOT Assist section before using this system, including how to operate it and how to interpret the display. When ProPILOT Assist is active and the status indicator A is illuminated in ...

    Diagnosis System (tcm)
    Diagnosis Description 1 Trip Detection Diagnosis and 2 Trip Detection Diagnosis NOTE: “Start the engine and turn OFF the ignition switch after warm-up.” This is defined as 1 trip. 1 TRIP DETECTION DIAGNOSISWhen initial malfunction is detected, TCM memorizes DTC. In these diagnoses, some ...

    Removal and Installation. Fender Protector
    Exploded View Front fender protector Clip nut Splash guard Fender clip Screw grommet     : Nissan Ariya Vehicle front Removal and Installation REMOVALRemove front spoiler. Refer to Removal and Installation. Remove front fillet molding. Refer to Re ...