Nissan Rogue (T33) 2021-Present Service Manual: It Can Communication 1 Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Electrical & Power Control :: Lan System / Can :: Dtc/circuit Diagnosis / It Can Communication 1 Circuit

Diagnosis Procedure

CHECK NETWORK DIAGNOSIS

Check the "Network diagnosis" results from CONSULT to see that the diagnostic CAN communication circuit have no malfunction.

Are the diagnostic CAN communication circuit normal?

YES>>

GO TO 2.

NO>>

Check and repair diagnostic CAN communication circuit.

CONNECTOR INSPECTION

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect all the unit connectors on IT CAN communication 1 circuit.

  4. Check terminals and connectors for damage, bend and loose connection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the connector of 8CH CAN gateway.

  2. Check the continuity between the 8CH CAN gateway harness connector terminals.

    8CH CAN gateway harness connector Continuity
    Connector No. Terminal No. Connector No. Terminal No.
    M45 25 M9 55 Existed
    26 56 Existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Check the harness and repair or replace the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the 8CH CAN gateway harness connector terminals.

8CH CAN gateway harness connector Continuity
Connector No. Terminal No.
M45 25 26 Not existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Check the harness and repair the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the 8CH CAN gateway and the ground.

8CH CAN gateway harness connector Ground Continuity
Connector No. Terminal No.
M45 25 Not existed
26 Not existed

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Check the harness and repair the root cause.

CHECK 8CH CAN GATEWAY TERMINATION CIRCUIT

  1. Remove the 8CH CAN gateway.

  2. Check the resistance between the 8CH CAN gateway terminals.

    8CH CAN gateway Resistance (Ω)
    Terminal No.
    25 26 Approx. 108 – 132
    55 56 Approx. 108 – 132

Is the measurement value within the specification?

YES>>

GO TO 7.

NO>>

Replace the 8CH CAN gateway.

CHECK SYMPTOM

Connect all the connectors. Check if the symptoms described in the “Symptom (Results from interview with customer)” are reproduced.

Inspection result

Reproduced>>

GO TO 7.

Non-reproduced>>

Start the diagnosis again. Follow the trouble diagnosis procedure when past error is detected.

CHECK UNIT REPRODUCTION

Perform the reproduction test as per the following procedure for each unit.

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect one of the unit connectors of IT CAN communication 1 circuit.

    NOTE:

    8CH CAN gateway has two termination circuits. Check other units first.

  4. Connect the battery cable to the negative terminal. Check if the symptoms described in the “Symptom (Results from interview with customer)” are reproduced.

    NOTE:

    Although unit-related error symptoms occur, do not confuse them with other symptoms.

Inspection result

Reproduced>>

Connect the connector. Check other units as per the above procedure.

Non-reproduced>>

Replace the unit whose connector was disconnected.

    It Can Communication Circuit
    Diagnosis Procedure CHECK NETWORK DIAGNOSIS Check the "Network diagnosis" results from CONSULT to see that the diagnostic CAN communication circuit have no malfunction. Are the ...
    It Can Communication 2 Circuit
    Diagnosis Procedure CHECK NETWORK DIAGNOSIS Check the "Network diagnosis" results from CONSULT to see that the diagnostic CAN communication circuit have no malfunction. Are the ...

    Other materials:

    Gestion intelligente du chargement et rangements du Nissan Rogue
    Plancher de compartiment à bagages unique Le coffre de votre Nissan Rogue est équipé d'un plancher robuste maintenu par deux goupilles de retenue (A) pour une stabilité maximale. Pour retirer ce panneau sans risquer d'endommager les fixations ou les garnitures intérieures de votre Nissan ...

    Tcm
    Exploded View 1. Transaxle assembly 2. TCM 3. gasket : N·m (kg-m, in-lb) : Vehicle front Removal and Installation Never Reuse These Parts Part Code For additional information: Gasket-TCM – TCM-Exploded View CAUTION: Never impact the TCM when removing o ...

    C1f03-72 Stop Lamp Relay
    Without Propilot Assist 2.1 DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition   C1F03 72 OPERATION SW CIRC (Operation switch circuit) Diagnosis condition When engine is running When AEB system is ...