Nissan Rogue (T33) 2021-Present Service Manual: Intelligent Around View Monitor :: Symptom Diagnosis
Intelligent Around View Monitor
Symptom Table
INTELLIGENT AROUND VIEW MONITOR SYSTEM
| Symptoms | Check items | Probable malfunction location | |
|---|---|---|---|
| Screen is not switched to camera image, when camera switch is pressed and when shift position is shifted to the reverse position. | “AVM” is not displayed on the system selection screen of CONSULT. | Around view monitor control unit power supply circuit | |
|
Check that the following "DATA MONITOR" items operate normally using CONSULT
|
"CAMERA SWITCH SIGNAL" and "REVERSE SIGNAL" are normal | Around view monitor control unit | |
| "CAMERA SWITCH SIGNAL" or "REVERSE SIGNAL" is not normal | CAN communication | ||
| Screen is switched when pressing camera switch or shifting selector lever to the reverse position, however, all views are not displayed. | Only superimposing is displayed (only images that AV control unit plots are displayed). | LVDS (between around view monitor control unit and each camera) | |
| Superimposing is not displayed. | AV control unit or LVDS (between around view monitor control unit and AV control unit) | ||
| The screen is not switched to the rear view image even if the selector is shifted to the reverse position. | The front view is displayed normally. | CAN communication (Reverse signal) | |
|
Check the following "DATA MONITOR" items using CONSULT.
|
NG | LVDS (between front camera and around view monitor control unit) |
| OK | Front camera | ||
|
Check the following "DATA MONITOR" items using CONSULT.
|
NG | LVDS (between rear camera and around view monitor control unit) |
| OK | Rear camera | ||
|
Check the following "DATA MONITOR" items using CONSULT.
|
NG | LVDS (between side camera LH and around view monitor control unit) |
| OK | Side camera LH | ||
| Right side of top view image is not displayed. |
Check the following "DATA MONITOR" items using CONSULT.
|
NG | LVDS (between side camera RH and around view monitor control unit) |
| OK | Side camera RH | ||
Normal Operating Condition
Symptom Table
NOTE:
For Navigation system operation information, refer to Navigation system Owner's Manual.
BASIC OPERATIONS
| Symptom | Possible cause | Possible solution |
|---|---|---|
| No image is displayed. | The brightness is at the lowest setting. | Adjust the brightness of the display. |
| The systems in the video mode. | Press “DISC-AUX” to change the mode. | |
| The display is turned off. | Press “ -” to turn on the display. |
|
| The interior of the Nissan Ariya vehicle becomes the a little less than 80°C (176°F) or high temperature, and the protection of the display acts, and a display is turned off. | Wait until the interior of the Nissan Ariya vehicle has cooled down. | |
| Screen not clear. | Contrast setting is not appropriate. | Adjust the contrast of the display. |
| No voice guidance is available. Or The volume is too high or too low. | The volume is not set correctly, or it is turned off. | Adjust the volume of voice guidance. |
| Voice guidance is not provided for certain streets (roads displayed in gray). | This is not a malfunction. | |
| No map is displayed on the screen. | A screen other than map screen is displayed. | Press “MAP”. |
| The screen is too dim. The movement is slow. | The temperature in the interior of the Nissan Ariya vehicle is low. | Wait until the interior of the vehicle has warmed up. |
| Some pixels in the display are darker or brighter than others. | This condition is an inherent characteristic of liquid crystal displays. | This is not a malfunction. |
| Some menu items cannot be selected. | Some menu items become unavailable while the Nissan Ariya vehicle is driven. | Park the vehicle in a safe location, and then operate the navigation system. |
NOTE:
Locations stored in the Address Book and other memory functions may be lost if the Nissan Ariya vehicle's battery is disconnected or becomes discharged. If this occurs, service the vehicle's battery as necessary and re-enter the information in the Address Book.
Other materials:
Abs Branch Line Circuit
Diagnosis Procedure
CHECK CONNECTOR
Turn the ignition switch OFF.
Disconnect the battery cable from the negative terminal.
Check the following terminals and connectors for damage, bend and loose connection (unit side and connector side).
ABS actuator and electric unit (control u ...
Illumination Control Switch Signal Circuit
Component Function Check
CHECK COMBINATION METER INPUT SIGNAL
Ignition switch ON.
Measure voltage between the following terminals of the combination meter.
Combination meter
Condition
Voltage
(Approx.)
Connector
Terminals
(+)
(−)
M73 (U.S.A. production)
...
Dtc/circuit Diagnosis. B2920-09 Driver Seat Control Unit
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen items
(Trouble diagnosis content) DTC detection condition
B2920-09
Driver seat control unit
(Driver seat control unit)
Diagnosis condition
The power consumption control of driver seat control unit is in wake-up state
...

-” to turn on the display.