Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Rear Washer Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Controls :: Wiper & Washer / Dtc/circuit Diagnosis :: Rear Washer Circuit

Component Function Check

CHECK REAR WASHER OPERATION

When the rear washer switch is turned to the ON position the rear washer should operate.

Is rear washer operation normal?

YES>>

Washer switch circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

COMBINATION SWITCH INSPECTION

Check combination switch. Refer to Symptom Table.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace the malfunctioning part.

CHECK FRONT AND REAR WASHER PUMP FUSE

  1. Ignition switch OFF.

  2. Check that the following fuse is not blown (open):

    Location No. Capacity
    IPDM E/R 81 15A

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit.

NO>>

GO TO 3.

CHECK REAR WASHER PUMP RELAY OUTPUT VOLTAGE

  1. Ignition switch OFF.

  2. Disconnect front and rear washer pump relay connector.

  3. Ignition switch ON.

  4. Check voltage between front and rear washer pump relay harness connector and ground.

    (+) (−)

    Voltage

    (Approx.)
    Front and rear washer pump relay
    Connector Terminal
    E39 7 Ground Battery voltage
    8

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 4.

CHECK REAR WASHER PUMP RELAY CIRCUIT 1

  1. Ignition switch OFF.

  2. Disconnect IPDM E/R connector.

  3. Check continuity between IPDM E/R harness connector and front and rear washer pump relay harness connector.

    IPDM E/R Front and rear washer pump relay Continuity
    Connector Terminal Connector Terminal
    E121 43 E39 7 Yes
    8

  4. Check continuity between IPDM E/R harness connector and ground.

    IPDM E/R (—) Continuity
    Connector Terminal
    E121 43 Ground No

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK REAR WASHER PUMP RELAY CIRCUIT 2

  1. Ignition switch OFF.

  2. Connect front and rear washer pump relay connector.

  3. Ignition switch ON.

  4. Check voltage between front and rear washer pump relay harness connector and ground.

    (+) (−) Condition

    Voltage

    (Approx.)
    Front and rear washer pump relay
    Connector Terminal
    E39 9 Ground Rear washer switch ON 0 V
    OFF Battery voltage

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

GO TO 6.

CHECK REAR WASHER PUMP RELAY CIRCUIT 3

  1. Ignition switch OFF.

  2. Disconnect IPDM E/R connector and front and rear washer pump relay connector.

  3. Check continuity between IPDM E/R harness connector and front and rear washer pump relay harness connector.

    IPDM E/R Front and rear washer pump relay Continuity
    Connector Terminal Connector Terminal
    E119 6 E39 9 Yes

  4. Check continuity between IPDM E/R harness connector and ground.

    IPDM E/R (—) Continuity
    Connector Terminal
    E119 6 Ground No

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK REAR WASHER PUMP RELAY

Check rear washer pump relay. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Replace rear washer pump relay.

CHECK FRONT AND REAR WASHER PUMP CIRCUIT 1

  1. Check continuity between front and rear washer pump harness connector and front and rear washer pump relay harness connector.

    Front and rear washer pump Front and rear washer pump relay Continuity
    Connector Terminal Connector Terminal
    E41 1 E39 6 Yes

  2. Check continuity between front and rear washer pump relay harness connector and ground.

    Front and rear washer pump relay (—) Continuity
    Connector Terminal
    E39 6 Ground No

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Repair or replace harness.

CHECK FRONT AND REAR WASHER PUMP CIRCUIT 2

  1. Check continuity between front and rear washer pump harness connector and front and rear washer pump relay harness connector.

    Front and rear washer pump Front and rear washer pump relay Continuity
    Connector Terminal Connector Terminal
    E41 2 E39 1 Yes

  2. Check continuity between front and rear washer pump relay harness connector and ground.

    Front and rear washer pump relay (—) Continuity
    Connector Terminal
    E39 1 Ground No

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair or replace harness.

CHECK FRONT WASHER PUMP RELAY

Check front washer pump relay. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

Replace front washer pump relay.

CHECK REAR WASHER PUMP GROUND OPEN CIRCUIT

Check continuity between front and rear washer pump relay harness connector and ground.

Front and rear washer pump relay (—) Continuity
Connector Terminal
E39 5 Ground Yes

Is the inspection result normal?

YES>>

Replace front and rear washer pump. Refer to Removal and Installation.

NO>>

Repair or replace harness.

Component Inspection

CHECK REAR WASHER PUMP RELAY

  1. Ignition switch OFF.

  2. Disconnect rear washer pump relay connector.

  3. Check continuity between rear washer pump relay terminals.

    Rear washer pump relay Condition Continuity
    Terminal
    6 7 12 V direct current supply between terminals 8 and 9. Yes
    No current supply No
    10 12 V direct current supply between terminals 8 and 9. No
    No current supply Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace rear washer pump relay.

    Dtc/circuit Diagnosis. Front Washer Circuit
    Component Function Check CHECK FRONT WASHER OPERATION When the front washer switch is turned to the ON position the front washer should operate. Is front washer operation normal...
    Dtc/circuit Diagnosis. Rain and Light Sensor
    Component Function Check CHECK FRONT WIPER AUTO OPERATION Clean the rain and light sensor detection area of windshield fully. When the front wiper switch is turned to AUTO posit...

    Other materials:

    Brake fluid
    For more information on brake fluid type and capacity, refer to “Capacities and recommended fluids/lubricants”. WARNING Always use new brake fluid from a sealed container. Contaminated, old, or poor-quality fluid may damage the brake system and reduce stopping performance. Clean the filler c ...

    U2454-87 Can Comm Circuit
    Without Propilot Assist 2.1 DTC Description CAN COMMUNICATIONCAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Ariya vehicle multiplex communication line with high data communication speed and excellent error detection ability. Mode ...

    Dtc/circuit Diagnosis. B0038-11 Rear Side A/b Module Rh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B0038-11 REAR SIDE A/B MODULE RH (Second Row Right Side Airbag Deployment Control) Diagnosis condition When ignition switch is ON. Signal (terminal) Rear si ...