Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Power Supply and Ground Circuit
Front Door Lock
Diagnosis Procedure
CHECK FUSE
Check that the following fuse is not blown (open).
| Signal name | Fuse No. |
|---|---|
| Front door lock actuator power supply | 12 (10 A) |
Is the fuse blown (open)?
YES>>Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).
NO>>GO TO 2.
CHECK POWER SUPPLY CIRCUIT
-
Ignition switch OFF.
-
Disconnect BCM connector.
-
Check voltage between BCM harness connector and ground.
(+) (−) Voltage
(Approx.)BCM Connector Terminal B23 (with type B meter)
B124 (with type A meter)135 Ground Battery voltage
Is the measurement value normal?
YES>>GO TO 3.
NO>>Repair or replace harness.
CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
| BCM | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| B23 | 129 | Ground | Yes |
| 137 | |||
| BCM | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| B124 | 132 | Ground | Yes |
| 140 | |||
Is the inspection result normal?
YES>>Inspection End.
NO>>Repair or replace harness.
Rear Door Lock
Diagnosis Procedure
CHECK FUSE
Check that the following fuse is not blown (open).
| Signal name | Fuse No. |
|---|---|
| Rear door lock actuator power supply | 14 (10 A) |
Is the fuse blown (open)?
YES>>Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).
NO>>GO TO 2.
CHECK POWER SUPPLY CIRCUIT
-
Ignition switch OFF.
-
Disconnect BCM connector.
-
Check voltage between BCM harness connector and ground.
(+) (−) Voltage
(Approx.)BCM Connector Terminal B23 (with type B meter)
B124 (with type A meter)144 Ground Battery voltage
Is the measurement value normal?
YES>>GO TO 3.
NO>>Repair or replace harness.
CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
| BCM | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| B23 | 129 | Ground | Yes |
| 137 | |||
| BCM | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| B124 | 132 | Ground | Yes |
| 140 | |||
Is the inspection result normal?
YES>>Inspection End.
NO>>Repair or replace harness.
Automatic Back Door Control Unit
Diagnosis Procedure
CHECK FUSIBLE LINK
Check that the following fusible link is not blown (open).
| Fusible link No. | Signal name |
|---|---|
| JJ (30 A) | Battery power supply |
Is the fusible link blown (open)?
YES>>Replace the blown (open) fusible link after repairing the affected circuit if a fusible link is blown (open).
NO>>GO TO 2.
CHECK POWER SUPPLY CIRCUIT
-
Ignition switch OFF.
-
Disconnect automatic back door control unit connector.
-
Check voltage between automatic back door control unit harness connector and ground.
(+) (−) Voltage
(Approx.)Automatic back door control unit Connector Terminal B56 37 Ground Battery voltage
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace harness.
CHECK GROUND CIRCUIT
Check continuity between automatic back door control unit harness connector and ground.
| Automatic back door control unit | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| B56 | 42 | Ground | Yes |
Is the inspection result normal?
YES>>Inspection End.
NO>>Repair or replace harness.
Intelligent Key Unit
Diagnosis Procedure
CHECK FUSE
Check that the following fuse is not blown (open).
| Signal name | Fuse No. |
|---|---|
| Battery power supply | 53 (5 A) |
Is the fuse blown (open)?
YES>>Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).
NO>>GO TO 2.
CHECK POWER SUPPLY CIRCUIT
-
Disconnect Intelligent Key unit connector.
-
Check voltage between Intelligent Key unit harness connector and ground.
USA production models (+) (−) Voltage
(Approx.)Intelligent Key unit Connector Terminal M184 1 Ground Battery voltage Japan production models (+) (−) Voltage
(Approx.)Intelligent Key unit Connector Terminal M189 1 Ground Battery voltage
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace harness.
CHECK GROUND CIRCUIT
Check continuity between Intelligent Key unit harness connector and ground.
| Intelligent Key unit | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| M184 | 29 | Ground | Yes |
| Intelligent Key unit | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| M189 | 29 | Ground | Yes |
Is the inspection result normal?
YES>>Inspection End.
NO>>Repair or replace harness.
Hands Free Sensor Control Unit
Diagnosis Procedure
CHECK FUSE
Check that the following fuse is not blown (open).
| Signal name | Fuse No. |
|---|---|
| Battery power supply | 26 (10 A) |
Is the fuse blown (open)?
YES>>Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).
NO>>GO TO 2.
CHECK POWER SUPPLY CIRCUIT
-
Ignition switch OFF.
-
Disconnect hands free sensor control unit connector.
-
Check voltage between hands free sensor control unit harness connector and ground.
(+) (−) Voltage
(Approx.)Hands free sensor control unit Connector Terminal B452 2 Ground Battery voltage
Is the measurement value normal?
YES>>GO TO 3.
NO>>Repair or replace harness.
CHECK GROUND CIRCUIT
Check continuity between hands free sensor control unit harness connector and ground.
| Hands free sensor control unit | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| B452 | 3 | Ground | Yes |
Is the inspection result normal?
YES>>Inspection End.
NO>>Repair or replace harness.
Other materials:
Transfer Oil Temperature Sensor
Component Inspection
CHECK TRANSFER OIL TEMPERATURE SENSOR
Ignition switch OFF.
Remove transfer oil temperature sensor. Refer to Removal and Installation.
Check the resistance between transfer oil temperature sensor connector terminals.
Make measuring condition using burning hot ...
Plug
Description
Replace the O-ring if oil leaks from the plug.
Exploded View
1.
Plug
2.
O-ring
3.
Plug
4.
O-ring
5.
O-ring
6.
Overflow plug
7.
O-ring
8.
Transaxle assembly
: N·m (kg-m, ft-lb) : N·m (kg-m, in-lb) : Always replace ...
With Idle Start/stop. Symptom Diagnosis. Charging System
Charging System
Symptom Table
Symptom Reference
Discharged 12V battery
Refer to Work Flow (With EXP-800 NI or GR8-1200 NI) or Work Flow (Without EXP-800 NI or GR8-1200 NI).
The charge warning lamp does not illuminate when the ignition switch is set to ON.
The charge warning lamp ...
