Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Lithium Ion Battery 12v

Nissan Rogue (T33) 2021-Present Service Manual / Electrical & Power Control :: Power Supply, Ground & Circuit Elements / Dtc/circuit Diagnosis :: Lithium Ion Battery 12v

P1a00-49 Lithium Ion Battery 12v

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis contents) 		DTC detection condition
P1A00-49

Lithium ion battery 12V

(Lithium ion battery 12V) 		Diagnosis condition When ignition switch is ON
Signal (terminal) —
Threshold 12V sub battery (lithium ion battery) circuit malfunction
Diagnosis delay time 5 seconds or more

NOTE:

DTC "P1A00- 49" may be detected with DTC "P1A01-A3".

POSSIBLE CAUSE

12V sub battery (lithium ion battery)

FAIL-SAFE

Lithium ion battery 12V stopped (cancel stop/start system)

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Place ignition switch ON and wait at least 5 seconds or more.

  2. Check if the “P1A00-49” is detected as the current malfunction in “Self Diagnostic Result” of “Lithium ion battery 12V”.

Is DTC “P1A00-49” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC "P1A00-49" detected again?

YES>>

Replace 12V sub battery (lithium ion battery). Refer to Removal and Installation.

NO>>

Inspection End.

P1a01-A2 Lithium Ion Battery 12v

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis contents) 		DTC detection condition
P1A01-A2

Lithium ion battery 12V

(Lithium ion battery 12V) 		Diagnosis condition When ignition switch is ON
Signal (terminal) —
Threshold 12V sub battery (lithium ion battery) voltage drop
Diagnosis delay time 5 seconds or more

POSSIBLE CAUSE

12V sub battery (lithium ion battery)

FAIL-SAFE

Lithium ion battery 12V stopped (cancel stop/start system)

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Place ignition switch ON and wait at least 5 seconds or more.

  2. Check if the “P1A01-A2” is detected as the current malfunction in “Self Diagnostic Result” of “Lithium ion battery 12V”.

Is DTC “P1A01-A2” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC "P1A01-A2" detected again?

YES>>

Replace 12V sub battery (lithium ion battery). Refer to Removal and Installation.

NO>>

Inspection End.

P1a01-A3 Lithium Ion Battery 12v

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis contents) 		DTC detection condition
P1A01-A3

Lithium ion battery 12V

(Lithium ion battery 12V) 		Diagnosis condition When ignition switch is ON
Signal (terminal) —
Threshold 12V sub battery (Li-ion battery) overvoltage
Diagnosis delay time 5 seconds or more

NOTE:

DTC "P1A01-A3" may be detected with DTC "P1A00- 49".

POSSIBLE CAUSE

  • 12V battery

  • 12V sub battery (lithium ion battery) power supply harness

  • 12V sub battery (lithium ion battery)

FAIL-SAFE

Lithium ion battery 12V stopped (cancel stop/start system)

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Place ignition switch ON and wait at least 5 seconds or more.

  2. Check if the “P1A01-A3” is detected as the current malfunction in “Self Diagnostic Result” of “Lithium ion battery 12V”.

Is DTC “P1A01-A3” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

12V BATTERY VOLTAGE CHECK

CONSULT

  1. Ignition switch OFF.

  2. Check 12V battery voltage.

Is the voltage 11 V or less?

YES>>

Check 12V battery. Refer to Work Flow.

NO>>

GO TO 2.

12V SUB BATTERY (LITHIUM ION BATTERY) POWER SUPPLY HARNESS CHECK

  1. Disconnect negative terminal of 12V sub battery (lithium ion battery).

  2. Disconnect the 12V sub battery (lithium ion battery) connector.

  3. Check the continuity between 12V sub battery (lithium ion battery) harness connector and ground.

    + − Continuity
    12V sub battery (lithium ion battery)
    Connector Terminal
    B143 1 Ground No

Is the inspection result normal?

YES>>

Replace 12V sub battery (lithium ion battery). Refer to Removal and Installation.

NO>>

Repair or replace harness or connector.

P1a04-97 Lithium Ion Battery 12v

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis contents) 		DTC detection condition
P1A04-97

Lithium ion battery 12V

(Lithium ion battery 12V) 		Diagnosis condition When ignition switch is ON
Signal (terminal) —
Threshold 12V sub battery (lithium ion battery) low temperature
Diagnosis delay time 5 seconds or more

POSSIBLE CAUSE

12V sub battery (lithium ion battery)

FAIL-SAFE

Lithium ion battery 12V stopped (cancel stop/start system)

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Place ignition switch ON and wait at least 5 seconds or more.

  2. Check if the “P1A04-97” is detected as the current malfunction in “Self Diagnostic Result” of “Lithium ion battery 12V”.

Is DTC “P1A04-97” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair:Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC "P1A04-97" detected again?

YES>>

Replace 12V sub battery (lithium ion battery). Refer to Removal and Installation.

NO>>

Inspection End.

P1a04-98 Lithium Ion Battery 12v

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis contents) 		DTC detection condition
P1A04-98

Lithium ion battery 12V

(Lithium ion battery 12V) 		Diagnosis condition When ignition switch is ON
Signal (terminal) —
Threshold 12V sub battery (lithium ion battery) high temperature
Diagnosis delay time 5 seconds or more

POSSIBLE CAUSE

12V sub battery (lithium ion battery)

FAIL-SAFE

Lithium ion battery 12V stopped (cancel stop/start system)

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Place ignition switch ON and wait at least 5 seconds or more.

  2. Check if the “P1A04-98” is detected as the current malfunction in “Self Diagnostic Result” of “Lithium ion battery 12V”.

Is DTC “P1A04-98” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC "P1A04-98" detected again?

YES>>

Replace 12V sub battery (lithium ion battery). Refer to Removal and Installation.

NO>>

Inspection End.

P1a06-18 Lithium Ion Battery 12v

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis contents) 		DTC detection condition
P1A06-18

Lithium ion battery 12V

(Lithium ion battery 12V) 		Diagnosis condition When ignition switch is ON
Signal (terminal) —
Threshold 12V sub battery (lithium ion battery) over current (discharge side)
Diagnosis delay time 5 seconds or more

POSSIBLE CAUSE

12V sub battery (lithium ion battery)

FAIL-SAFE

Lithium ion battery 12V stopped (cancel stop/start system)

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Place ignition switch ON and wait at least 5 seconds or more.

  2. Check if the “P1A06-18” is detected as the current malfunction in “Self Diagnostic Result” of “Lithium ion battery 12V”.

Is DTC “P1A06-18” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC "P1A06-18" detected again?

YES>>

Replace 12V sub battery (lithium ion battery). Refer to Removal and Installation.

NO>>

Inspection End.

P1a06-19 Lithium Ion Battery 12v

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis contents) 		DTC detection condition
P1A06-19

Lithium ion battery 12V

(Lithium ion battery 12V) 		Diagnosis condition When ignition switch is ON
Signal (terminal) —
Threshold 12V sub battery (lithium ion battery) over current (charging side)
Diagnosis delay time 5 seconds or more

POSSIBLE CAUSE

12V sub battery (lithium ion battery)

FAIL-SAFE

Lithium ion battery 12V stopped (cancel stop/start system)

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Place ignition switch ON and wait at least 5 seconds or more.

  2. Check if the “P1A06-19” is detected as the current malfunction in “Self Diagnostic Result” of “Lithium ion battery 12V”.

Is DTC “P1A06-19” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC "P1A06-19" detected again?

YES>>

Replace 12V sub battery (lithium ion battery). Refer to Removal and Installation.

NO>>

Inspection End.

U0075-00 Can Comm Circuit

DTC Description

DESCRIPTION

CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Ariya vehicle multiplex communication line with high data communication speed and excellent error detection ability. Modern Nissan Ariya vehicle is equipped with many electronic control unit, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with 2 communication lines (CAN H-line, CAN L-line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only. CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC Detection Condition
U0075-00

Control module comm Bus C Off

(Control module communication Bus C Off) 		Diagnosis condition Ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold 12V sub battery (lithium ion battery) cannot communicate CAN communication signal.
Diagnosis delay time 2 seconds or more.

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select "Self Diagnostic Result" mode of "Lithium ion battery 12V" using CONSULT.

  3. Check DTC.

Is DTC "U0075-00" detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC "U0075-00" detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U2148-87 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis contents) 		DTC detection condition
U2148-87

CAN comm err (brake control unit)

(CAN communication err (brake control unit)) 		Diagnosis condition When ignition switch is ON
Signal (terminal) CAN communication signal
Threshold Signal transmission and reception error between 12V sub battery (lithium ion battery) and ABS actuator and electric unit (control unit)
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication

FAIL-SAFE

12V sub battery (lithium ion battery) does not work

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select "Self Diagnostic Result" mode of "Lithium ion battery 12V" using CONSULT.

  3. Check DTC.

Is DTC "U2148‐87" detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC "U2148-87" detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U214f-87 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(CAN comm err (BCM)) 		DTC detection condition
U214F-87

CAN comm err (BCM)

[CAN communication err (body control module)] 		Diagnosis condition When ignition switch is ON
Signal (terminal) CAN communication signal
Threshold Signal transmission and reception error between 12V sub battery (lithium ion battery) and BCM
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication

FAIL-SAFE

12V sub battery (lithium ion battery) does not work

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select "Self Diagnostic Result" mode of "Lithium ion battery 12V" using CONSULT.

  3. Check DTC.

Is DTC "U214F‐87" detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC "U214F-87" detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U2150-87 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
U2150–87

CAN comm err (AIRBAG)

[CAN communication error (AIRBAG)] 		Diagnosis condition When ignition switch is ON
Signal (terminal) CAN communication signal
Threshold Communication error
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system (AIRBAG)

FAIL-SAFE

The system using the CAN communication signal from control unit which cannot communicate does not function.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Turn ignition switch OFF and wait for 30 seconds.

  3. Turn ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “Lithium ion battery 12V” using CONSULT.

  5. Check DTC.

Is DTC “U2150-87” detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC "U2150-87" detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U215b-87 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis contents) 		DTC detection condition
U215B-87

CAN comm err (IPDM E/R)

[CAN communication err (IPDM E/R)] 		Diagnosis condition When ignition switch is ON
Signal (terminal) CAN communication signal
Threshold Signal transmission and reception error between 12V sub battery (lithium ion battery) and IPDM E/R
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication

FAIL-SAFE

12V sub battery (lithium ion battery) does not work

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select "Self Diagnostic Result" mode of "Lithium ion battery 12V" using CONSULT.

  3. Check DTC.

Is DTC "U215B‐87" detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC "U215B-87" detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U2176-87 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC Detection Condition
U2176-87

CAN comm err (CCM/ST angle sensor)

[CAN communication error (chassis control module/steering angle sensor)] 		Diagnosis condition Ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold 12V sub battery (lithium ion battery) cannot communicate CAN communication signal.
Diagnosis delay time 2 seconds or more.

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Perform “Self Diagnostic Result” mode of “Lithium ion battery 12V” using CONSULT.

Is DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC "U2176-87" detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

    Basic Inspection. Fusible Link Inspection
    How To Check A melted fusible link can be detected either by visual inspection or by feeling with finger tip. If its condition is questionable, use circuit tester or test lamp. ...
    Dtc/circuit Diagnosis. Power Supply and Ground Circuit. Lithium Ion Battery 12v
    Lithium Ion Battery 12v Diagnosis Procedure CHECK FUSE Check that the following fuse is not blown. Signal name Fuse No. Capacity Battery power supply 109 10A Is the inspection r...

    Other materials:

    Service Data and Specifications (sds)
    Specifications Windshield washer fluid capacity Except for Canada 2.4 (2 1/2 US qt, 2 1/8 Imp qt) For Canada 5.0 (5 1/2 US qt, 4 3/8 Imp qt) Windshield washer fluid specification   Refer to Fluids and Lubricants. ...

    Car phone or CB radio
    When installing a car phone or CB radio in your Nissan Rogue, follow these precautions to avoid interference with electronic modules or wiring systems. WARNING Do not use a handheld cellular phone while driving. It is unsafe and may be prohibited in some regions. If a call must be made while the ...

    Limites du système de sonar
    AVERTISSEMENT Les limites du système de sonar sont décrites ci-dessous. Le non-respect de ces limites lors de la conduite du Nissan Rogue peut entraîner des blessures graves, voire mortelles. Lisez attentivement toutes les informations relatives aux limites du système de sonar présentées ...