Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Door Mirror Defogger

Nissan Rogue (T33) 2021-Present Service Manual / Driver Controls :: Defogger / Dtc/circuit Diagnosis :: Door Mirror Defogger

Component Function Check

CHECK DOOR MIRROR DEFOGGER FUNCTION

CONSULT

  1. Ignition switch ON.

  2. Select “Rear defogger” in “Active test” mode of "BCM".

  3. Touch “On”.

  4. Check that both side door mirror glasses are getting warmer.

    NOTE:

    When glass is hot, never start inspection until it is cool enough.

Is the inspection result normal?

YES>>

Door mirror defogger function is OK.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK FUSE

  1. Ignition switch OFF.

  2. Check that the following fuse is not blown (open).

    Unit Location Fuse No. Capacity
    Door mirror defogger Fuse block (J/B) #2 10A

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 2.

CHECK DOOR MIRROR LH POWER SUPPLY CIRCUIT 1

  1. Disconnect door mirror LH connector.

  2. Start engine.

  3. Check voltage between door mirror LH harness connector and ground.

    With automatic drive positioner system
    (+) (–) Condition

    Voltage

    (Approx.)
    Door mirror LH
    Connector Terminal
    D16 1 Ground Rear window defogger switch ON Battery voltage
    OFF 0 V
    Without automatic drive positioner system
    (+) (–) Condition

    Voltage

    (Approx.)
    Door mirror LH
    Connector Terminal
    D14 6 Ground Rear window defogger switch ON Battery voltage
    OFF 0 V

Is the inspection result normal?

YES>>

Inspection End.

NO>>

GO TO 3.

CHECK DOOR MIRROR LH POWER SUPPLY CIRCUIT 2

  1. Ignition switch OFF.

  2. Disconnect fuse block (J/B) connector.

  3. Check continuity between fuse block (J/B) harness connector and door mirror LH harness connector.

    With automatic drive positioner system
    Fuse block (J/B) Door mirror LH Continuity
    Connector Terminal Connector Terminal
    B32 5Q D16 1 Yes
    Without automatic drive positioner system
    Fuse block (J/B) Door mirror LH Continuity
    Connector Terminal Connector Terminal
    B32 5Q D14 6 Yes

Is the inspection result normal?

YES>>

Replace fuse block (J/B).

NO>>

Repair or replace harness.

    Dtc/circuit Diagnosis. Rear Window Defogger
    Component Function Check CHECK REAR WINDOW DEFOGGER FUNCTION CONSULT Ignition switch ON. Select “Rear defogger” in “Active test” mode of "BCM". Touch “On”. Check tha...
    Dtc/circuit Diagnosis. Door Mirror Defogger Lh
    Component Function Check CHECK DOOR MIRROR DEFOGGER LH FUNCTION CONSULT Ignition switch ON. Select “Rear defogger” in “Active test” mode of "BCM". Touch “On”. Check ...

    Other materials:

    Ipdm E/r. Basic Inspection
    Additional Service When Replacing Ipdm E/r Description After replaced IPDM E/R, it is necessary to perform control unit configuration with CONSULT (for details, refer to Work Procedure).AFTER REPLACEMENTWhen replacing IPDM E/R, write vehicle specification with CONSULT vehicle configuration.CAUTI ...

    Magnetic Clutch
    Component Function Check CHECK MAGNETIC CLUTCH OPERATION CONSULT Select “HVAC TEST” in “Active test” mode of “HVAC”. Touch “MODE 1”. With operating the test item, check magnetic clutch operation by listening and viewing. Does it operate normally? YES>> ...

    Dtc/circuit Diagnosis. Vanity Mirror Lamp Control Circuit
    Component Function Check CAUTION: Before performing the diagnosis, check that the following are normal: Interior room lamp power supply circuit Vanity mirror lamp bulb CHECK VANITY MIRROR LAMP OPERATION Ignition switch ON. With operating the sun visor (vanity mirror lamp s ...