Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: C18fd-18 Temperature Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake System / Dtc/circuit Diagnosis :: C18fd-18 Temperature Sensor

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
C18FD 18 Temperature sensor 1 Diagnosis condition When Ignition switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in temperature sensor [-43.6℃ (-46.48℉) or less].
Diagnosis delay time 1 second or less
2 Diagnosis condition When Ignition switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in temperature sensor [169℃ (336.2℉) or more].
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven Intelligent Brake Unit

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always Ignition switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

CAUTION:

Never operate the Nissan Ariya vehicle.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF to ON without depressing the brake pedal.

  2. Ignition switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  4. Ignition switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Ignition switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  8. Ignition switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18FD-18" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Ignition switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Ignition switch OFF to ON without depressing the brake pedal.

  3. Ignition switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  5. Ignition switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Ignition switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  9. Ignition switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FD-18" detected?

YES>>

GO TO 3.

NO>>

Inspection End.

CHECK CONNECTOR TERMINALS

  1. Ignition switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect Electrically-driven Intelligent Brake Unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

CONSULT

  1. Connect Electrically-driven Intelligent Brake Unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Ignition switch OFF to ON without depressing the brake pedal.

  4. Ignition switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  6. Ignition switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Ignition switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  10. Ignition switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FD-18" detected?

YES>>

GO TO 5.

NO>>

Inspection End.

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Ignition switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect Electrically-driven Intelligent Brake Unit harness connector.

  5. Check the Electrically-driven Intelligent Brake Unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

CONSULT

  1. Ignition switch OFF to ON without depressing the brake pedal.

  2. Ignition switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  4. Ignition switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Ignition switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  8. Ignition switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FD-18" detected?

YES>>

GO TO 7.

NO>>

Inspection End.

CHECK DATA MONITOR

CONSULT

  1. Ignition switch OFF to ON without depressing the brake pedal.

  2. Select “BRAKE”, “Data monitor” according this order.

  3. Check "Temperature 1" and "Temperature 2". Refer to Values On The Diagnosis Tool.

Is "Temperature " -50℃ (-58℉) or less, or 125℃ (257℉) or more?

YES>>

GO TO 8.

NO>>

GO TO 9.

CHECK MOTOR ROOM

Check for any locations of abnormal heating around the Electrically-driven Intelligent Brake Unit.

Are there any heated locations?

YES>>

Perform diagnosis of the heated locations, and wait for the temperature to fall. GO TO 9.

NO>>

Replace the Electrically-driven Intelligent Brake Unit. Refer to Removal & Installation.

PERFORM SELF-DIAGNOSIS (4)

CONSULT

  1. Ignition switch OFF to ON without depressing the brake pedal.

  2. Ignition switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  4. Ignition switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Ignition switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  8. Ignition switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FD-18" detected?

YES>>

Replace the Electrically-driven Intelligent Brake Unit. Refer to Removal & Installation.

NO>>

Inspection End.

    Dtc/circuit Diagnosis. C18fc-19 Temperature Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition C18FC 19 Temperature sensor 1 Diagnosis condition When Ignition switch is ON. Signal (te...
    Dtc/circuit Diagnosis. C18fd-19 Temperature Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition C18FD 19 Temperature sensor 1 Diagnosis condition When Ignition switch is ON. Signal (te...

    Other materials:

    Dtc/circuit Diagnosis. C18de-82 Brake Power Supply Back up Unit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition C18DE 82 Backup power supply unit communication Diagnosis condition When Ignition switch is ON. Signal (terminal) Brake power supply backup unit signal Threshold When a malfunct ...

    System
    Propilot Assist 2.1 System Description SYSTEM DIAGRAM Component Description ADAS control unit 2 ADAS Control Unit GNSS antenna ROOF ANTENNA AND ANTENNA FEEDER HD map module HD MAP MODULE Front camera unit Front Camera Unit Steering assist switch Steering As ...

    Engine Stand Setting
    Setting NOTE: Explained here is how to disassemble with engine stand supporting transaxle surface. When using different type of engine stand, note with difference in steps and etc. Remove the engine and the transaxle assembly from the vehicle, and separate the transaxle from the engine. Ref ...