Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: C18fa-44 Programing Incomplete

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake System / Dtc/circuit Diagnosis :: C18fa-44 Programing Incomplete

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
C18FA 44 Calibration incomplete Diagnosis condition When Ignition switch is ON.
Signal (terminal) —
Threshold When programming data is not same.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Programing is not complete

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always Ignition switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

CAUTION:

Never operate the Nissan Ariya vehicle.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF to ON without depressing the brake pedal.

  2. Ignition switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  4. Ignition switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Ignition switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  8. Ignition switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18FA-44" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

PERFORM PROGRAMMING

CONSULT

Perform programming. Refer to Work Procedure.

>>

GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

CONSULT

  1. Ignition switch OFF to ON without depressing the brake pedal.

  2. Ignition switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  4. Ignition switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Ignition switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  8. Ignition switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FA-44" detected?

YES>>

Replace the Electrically-driven Intelligent Brake Unit. Refer to Removal & Installation.

NO>>

Inspection End.

    Dtc/circuit Diagnosis. C18ec-01 Stroke Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition C18EC 01 Stroke sensor Diagnosis condition When Ignition switch is ON. Signal (terminal)...
    Dtc/circuit Diagnosis. U1fa1-86 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U1FA1 86 CAN communication error (ADAS control unit) 1 Diagnosis condition When Ignition...

    Other materials:

    Diagnosis System (power Network Separate Relay)
    CONSULT Function (POWER NETWORK SEPARATE RELAY) APPLICATION ITEMSCONSULT performs the following functions via CAN communication using power network separate relay. Diagnosis mode Description Self Diagnostic Result Displays DTC stored in power network separate relay Displays freeze ...

    Component Parts
    Propilot Assist 2.1 Component Parts Location A. Behind front bumper fascia No. Component Function 1. HD map antenna Refer to HD MAP MODULE. 2. Side radar rear RH Refer toComponent Parts Location for detailed component location. 3. Power network separate rel ...

    P04fa Egr Temperature
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P04FA 00 EGR A control (EGR "A" Control temperature Too High) Diagnosis condition — Signal (terminal) — Threshold ECM detects that a signal ...