Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: C18e3-86 Abs Actuator and Electric Unit (control Unit) System

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake System / Dtc/circuit Diagnosis :: C18e3-86 Abs Actuator and Electric Unit (control Unit) System

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
C18E3 86 VDC system Diagnosis condition When Ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When ABS actuator and electric unit (control unit) transmission signal is malfunction.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

ABS actuator and electric unit (control unit)

FAIL-SAFE

The following functions are suspended.

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always Ignition switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

CAUTION:

Never operate the Nissan Ariya vehicle.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF to ON without depressing the brake pedal.

  2. Ignition switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  4. Ignition switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Ignition switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  8. Ignition switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E3-86" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SYSTEM

Perform self-diagnosis for “ABS”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

CONSULT

  1. Ignition switch OFF to ON without depressing the brake pedal.

  2. Ignition switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  4. Ignition switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Ignition switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  8. Ignition switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E3-86" detected?

YES>>

GO TO 3.

NO>>

Inspection End.

CHECK 12V BATTERY

  1. Ignition switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Ignition switch OFF to ON without depressing the brake pedal.

  3. Ignition switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  5. Ignition switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Ignition switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  9. Ignition switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E3-86" detected?

YES>>

GO TO 5.

NO>>

Inspection End.

CHECK CONNECTOR TERMINALS

  1. Ignition switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect Electrically-driven Intelligent Brake Unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness, connector, or terminal. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

CONSULT

  1. Connect Electrically-driven Intelligent Brake Unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Ignition switch OFF to ON without depressing the brake pedal.

  4. Ignition switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  6. Ignition switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  8. Ignition switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  10. Ignition switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E3-86" detected?

YES>>

GO TO 7.

NO>>

Inspection End.

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Ignition switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect Electrically-driven Intelligent Brake Unit harness connector.

  5. Check the Electrically-driven Intelligent Brake Unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

CONSULT

  1. Ignition switch OFF to ON without depressing the brake pedal.

  2. Ignition switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  4. Ignition switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Ignition switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  8. Ignition switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E3-86" detected?

YES ("C18E3-86")>>

Replace the Electrically-driven Intelligent Brake Unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

YES (Other than "C18E3-86")>>

Check the DTC. Refer to DTC Index.

NO>>

Inspection End..

    Dtc/circuit Diagnosis. C18e1-4b Motor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition C18E1 4B Motor Diagnosis condition When Ignition switch is ON. Signal (terminal) — Thr...
    Dtc/circuit Diagnosis. C18e4-88 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition C18E4 88 CAN communication system 1 Diagnosis condition When Ignition switch is ON. Sign...

    Other materials:

    Dtc/circuit Diagnosis. Horn Function
    Component Function Check CHECK FUNCTION CONSULT Ignition switch OFF. Perform “Horn” in “Active test” mode of “IPDM E/R”. Check the horn operation. Test item Description Horn On Horn Sounds (for 20 ms.) Is the operation normal? YES>> Ins ...

    Drive Pinion
    Kr15ddt Exploded View Drive pinion lock nut Companion flange Dust shield Drive pinion oil seal Pinion bearing assembly O-ring Drive pinion adjusting shim Drive pinion O-ring Transfer case oil seal Dowel pin Plug Gasket T ...

    C106e-54 Steering Angle Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C106E 54 Steering angle sensor (Steering angle sensor) Diagnosis condition When ignition switch is ON. When the power supply voltage is normal. ...