Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: C161a-82 Abs System

Nissan Rogue (T33) 2021-Present Service Manual / Steering :: Steering Control System / Dtc/circuit Diagnosis :: C161a-82 Abs System

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C161A 82

ABS system

(Anti-lock braking system ) 		Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When a malfunction is detected in ABS actuator and electric unit (control unit).
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • CAN communication line

  • ABS actuator and electric unit (control unit)

  • Power steering control module

FAIL-SAFE

Constant steering assist level state

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

  1. Pull the parking brake switch.

    NOTE:

    Check to make sure that the parking brake switch indicator is turned ON.

  2. Ignition switch OFF.

  3. Get out of the Nissan Ariya vehicle and close all doors.

  4. Wait 65 seconds.

    NOTE:

    • Check to make sure that the parking brake switch indicator is turned OFF.

    • If the rear brake calipers are hot, wait up to an hour until parking brake indicator light on the switch turns OFF. Once indicator light on the switch turns OFF, move to next step.

>>

GO TO 2.

DTC REPRODUCTION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Perform self diagnosis for “EPS/Direct Adaptive Steering 3”.

Is DTC “C161A-82” detected?

YES>>

Proceed to diagnosis procedure. Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Ignition switch OFF to ON.

  2. Perform self diagnosis for "ABS".

Is any DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

CHECK CONNECTOR AND TERMINAL

  1. Ignition switch OFF.

  2. Disconnect ABS actuator and electric unit (control unit) harness connector.

  3. Disconnect power steering control module harness connector.

  4. Check the connector for disconnection or looseness.

  5. Check the terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness, connector, or terminal, securely lock the connector.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Connect ABS actuator and electric unit (control unit) harness connector.

  2. Connect power steering control module harness connector.

  3. Ignition switch OFF to ON.

  4. Erase self diagnosis results for “EPS/Direct Adaptive steering 3”.

  5. Pull the parking brake switch.

    NOTE:

    Check to make sure that the parking brake switch indicator is turned ON.

  6. Ignition switch OFF.

  7. Get out of the Nissan Ariya vehicle and close all doors.

  8. Wait 65 seconds.

    NOTE:

    • Check to make sure that the parking brake switch indicator is turned OFF.

    • If the rear brake calipers are hot, wait up to an hour until parking brake indicator light on the switch turns OFF. Once indicator light on the switch turns OFF, move to next step.

  9. Ignition switch ON.

  10. Perform self diagnosis for “EPS/Direct Adaptive Steering 3”.

Is DTC “C161A-82” detected?

YES>>

Replace the power steering control module (steering gear assembly). Refer to Removal and Installation.

NO>>

Inspection End.

    Dtc/circuit Diagnosis. C1615-4b Overheat
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1615 4B Control unit over heat (Control unit over heat) Dia...
    Dtc/circuit Diagnosis. U0076-00 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition U0076 00 Control module comm Bus D Off (Control module comm ...

    Other materials:

    Aluminum Repair
    Sheet Metal Work (aluminum) Sheet Metal Work (Aluminum) Repairing aluminum alloy panels is basically the same as repairing steel panels. Special considerations for repairing aluminum alloy are listed below. Sanding Aluminum alloy panels are softer than steel plates. It is important to se ...

    Système 4x4 Intelligent
    En cas de dysfonctionnement du système 4x4 Intelligent du Nissan Rogue alors que le moteur est en marche, différents messages d'avertissement peuvent s'afficher sur l'écran d'informations du véhicule afin d'informer le conducteur de l'état du système de transmission intégrale. Si l'a ...

    System Description. System
    System Description (Heated Steering Wheel) SYSTEM DIAGRAMThe heated steering wheel switch controls the heated steering wheel relay. When the heated steering wheel switch is turned on, the heated steering wheel relay is energized and the heated steering wheel system will operate. The heated ...