Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B2428-54 Automatic Back Door Control Unit

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock / Dtc/circuit Diagnosis :: B2428-54 Automatic Back Door Control Unit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC Detection Condition
B2428-54

Automatic back door control unit

(Automatic back door control unit) 		Diagnosis condition All times
Signal (terminal) —
Threshold When the calibration of [CALIBRATION OF AUTOMATIC BACK DOOR POSITION INFORMATION] is not complete
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

[CALIBRATION OF AUTOMATIC BACK DOOR POSITION INFORMATION]: not complete

FAIL-SAFE

Inhibit automatic back door system all function

DTC CONFIRMATION PROCEDURE

DTC CONFIRMATION

CONSULT

  1. Ignition switch ON.

  2. Select “Self diagnosis result” mode of “AUTOMATIC BACK DOOR”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CALIBRATION OF AUTOMATIC BACK DOOR POSITION INFORMATION

  1. Perform initialization setting of automatic back door position information. Refer to Work Procedure.

  2. Erase DTC, and then repeat “DTC CONFIRMATION PROCEDURE”. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 2.

NO>>

Inspection End.

CHECK CONNECTOR

  1. Ignition switch OFF.

  2. Check the automatic back door control unit harness connector for disconnection or looseness.

  3. Check the touch sensor RH harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair/replace harness or connector, and securely lock the connector.

CHECK AUTOMATIC BACK DOOR CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT

Check the automatic back door control unit power supply and ground circuits. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair/replace harness, connector, fuse, or fusible link, and GO TO 5.

CHECK TERMINAL

  1. Ignition switch OFF.

  2. Disconnect automatic back door control unit harness connector and then check the automatic back door control unit pin terminals for damage or loose connection with harness connector.

  3. Disconnect touch sensor RH harness connector and check touch sensor RH pin terminal for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

Replace automatic back door control unit. Refer to Removal and Installation.

NO>>

Repair/replace harness, connector, or terminal.

    Dtc/circuit Diagnosis. B2428-52 Automatic Back Door Control Unit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2428-52 Automatic back door control unit (Automatic back do...
    Dtc/circuit Diagnosis. B242a-11 Closure Motor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B242A-11 Closure motor (Closure motor) Diagnosis condition A...

    Other materials:

    Power Supply and Ground Circuit
    8ch Can Gateway Diagnosis Procedure CHECK FUSE Check that the following fuse are not blown. Signal name Fuse No. Battery power supply 16 Ignition power supply 9 Is the fuse blown (open)? YES>> Replace the blown fuse after repairing the affected circuit if a fuse ...

    Towing load/specification
    WARNING The towing capacities in this manual are general guidelines. Actual safe towing capacity of your Nissan Rogue depends on factory or dealer-installed equipment, passenger load, and cargo weight. You must weigh both the vehicle and trailer as described to determine true towing capacity. Never ...

    B2730-13 Side Sensor [rl]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B2730-13 SIDE SENSOR [RL] (Side sensor [RL]) Diagnosis condition When ignition switch is ON Signal (terminal) Rear sonar sensor signal LH side Threshold H ...