Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B0002-09 Driver Airbag Module 2

Nissan Rogue (T33) 2021-Present Service Manual / Restraints :: Srs Air Bag Control System / Dtc/circuit Diagnosis :: B0002-09 Driver Airbag Module 2

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC Detection Condition
B0002-09

DRIVER AIRBAG MODULE 2

(Driver Frontal Stage 2 Deployment Control) 		Diagnosis condition When ignition switch is ON.
Signal (terminal) Driver air bag module signal
Threshold

Driver air bag module circuit is shorted to other

(including the spiral cable)
Diagnosis delay time 2 seconds or more.

POSSIBLE CAUSE

  • Connection malfunction or short circuit of harness and connector

  • Internal malfunction of driver air bag module

  • Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAGNOSIS RESULT

CONSULT

  1. Ignition switch ON.

  2. Perform “Self diagnosis result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

WARNING:

  • Before servicing, ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.)

  • Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace wiring harness.

REPLACE SPIRAL CABLE

  1. Replace spiral cable. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 4.

NO>>

Inspection End

REPLACE DRIVER AIR BAG MODULE

  1. Replace driver air bag module. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 5.

NO>>

Inspection End

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

  1. Replace air bag diagnosis sensor unit. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 1.

NO>>

Inspection End

    Dtc/circuit Diagnosis. B0001-55 Driver Airbag Module
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B0001-55 DRIVER AIRBAG MODULE (Driver Frontal Stage 1 Deploy...
    Dtc/circuit Diagnosis. B0002-11 Driver Airbag Module 2
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B0002-11 DRIVER AIRBAG MODULE 2 (Driver Frontal Stage 2 Depl...

    Other materials:

    Power Socket. Removal and Installation. Power Socket
    Power Socket Console Power Socket Removal and Installation REMOVALRemove switch panel. Refer to Removal and Installation. Press the power socket fixing pawls from the back of the switch panel to remove the power socket. : Pawl INSTALLATIONNote the following, and install in the reve ...

    Electric Wastegate Control Actuator
    Component Inspection INSPECTION START Do you have CONSULT? Do you have CONSULT? YES>> GO TO 2. NO>> GO TO 3. CHECK ELECTRIC WASTEGATE CONTROL ACTUATOR With CONSULT Turn ignition switch ON and engine stopped. On the CONSULT screen, select “ENGINE”>>“ACTIVE ...

    Information Display (combination Meter)
    Door Open Warning DESIGN/PURPOSEInformation display warns the driver that each door is open or is not fully closed. Symbol Message – SYNCHRONIZATION WITH MASTER WARNING LAMPSynchronization is applied.Refer to Master Warning Lamp.SYSTEM DIAGRAMSIGNAL PATH BCM transmits door switch ...