Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Automatic Back Door Switch

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock / Dtc/circuit Diagnosis :: Automatic Back Door Switch

Component Function Check

CHECK FUNCTION

CONSULT

  1. Ignition switch ON.

  2. Select “Automatic back door switch” in “Data monitor” mode of "AUTOMATIC BACK DOOR".

  3. Check that the function operates normally according to the following conditions.

Monitor item Condition Status
Automatic back door switch Automatic back door switch Short pressed Short
Long pressed Long
Released Off

Is the inspection result normal?

YES>>

Automatic back door switch is OK.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK AUTOMATIC BACK DOOR SWITCH INPUT SIGNAL

  1. Ignition switch OFF.

  2. Disconnect automatic back door switch connector.

  3. Check voltage between automatic back door switch harness connector and ground.

    (+) (–)

    Voltage

    (Approx.)
    Automatic back door switch
    Connector Terminal
    M256 2 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK AUTOMATIC BACK DOOR SWITCH CIRCUIT

  1. Disconnect automatic back door control unit connector.

  2. Check continuity between automatic back door control unit harness connector and automatic back door switch harness connector.

    Automatic back door control unit Automatic back door switch Continuity
    Connector Terminal Connector Terminal
    B55 4 M256 2 Yes

  3. Check continuity between automatic back door control unit harness connector and ground.

    Automatic back door control unit — Continuity
    Connector Terminal
    B55 4 Ground No

Is the inspection result normal?

YES>>

Replace automatic back door control unit. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK AUTOMATIC BACK DOOR SWITCH GROUND CIRCUIT

Check continuity between automatic back door switch harness connector and ground.

Automatic back door switch — Continuity
Connector Terminal
M256 3 Ground Yes

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness.

CHECK AUTOMATIC BACK DOOR SWITCH

Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace automatic back door switch. Refer to Removal and Installation.

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

>>

Inspection End.

Component Inspection

CHECK AUTOMATIC BACK DOOR SWITCH

  1. Ignition switch OFF.

  2. Disconnect automatic back door switch connector.

  3. Check continuity between automatic back door switch terminals.

Automatic back door switch Condition Continuity
Terminal
2 3 Automatic back door switch Pressed Yes
Released No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace automatic back door switch. Refer to Removal and Installation.

    Dtc/circuit Diagnosis. Automatic Back Door Serial Communication
    Diagnosis Procedure CHECK AUTOMATIC BACK DOOR SERIAL COMMUNICATION SIGNAL Ignition switch ON. Check signal between BCM harness connector and ground using oscilloscope. (+) (–)...
    Dtc/circuit Diagnosis. Automatic Back Door Lock and Close Switch
    Component Function Check CHECK FUNCTION CONSULT Ignition switch ON. Select “Lock & close switch” in “Data monitor” mode of "AUTOMATIC BACK DOOR". Check that the func...

    Other materials:

    C1f76-49 Steering Angle Sensor
    Without Propilot Assist 2.1 DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition   C1F76 49 Steering angle sensor (Steering angle sensor) Diagnosis condition When engine is running When AEB system is ...

    Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses
    Work Flow CUSTOMER INTERVIEWInterview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diagnostic Worksheet during the interview to document the facts and conditions when the noise occurs and any of customer's comments; Refer to Diagnostic Work ...

    Electric Wastegate Control Actuator
    Component Inspection INSPECTION START Do you have CONSULT? Do you have CONSULT? YES>> GO TO 2. NO>> GO TO 3. CHECK ELECTRIC WASTEGATE CONTROL ACTUATOR With CONSULT Turn ignition switch ON and engine stopped. On the CONSULT screen, select “ENGINE”>>“ACTIVE ...