Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Automatic Back Door Lock and Close Switch

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock / Dtc/circuit Diagnosis :: Automatic Back Door Lock and Close Switch

Component Function Check

CHECK FUNCTION

CONSULT

  1. Ignition switch ON.

  2. Select “Lock & close switch” in “Data monitor” mode of "AUTOMATIC BACK DOOR".

  3. Check that the function operates normally according to the following conditions.

Monitor item Condition Status
Lock & close switch Automatic back door lock and close switch Pressed On
Released Off

Is the inspection result normal?

YES>>

Automatic back door lock and close switch is OK.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK AUTOMATIC BACK DOOR LOCK AND CLOSE SWITCH INPUT SIGNAL

  1. Ignition switch OFF.

  2. Disconnect automatic back door lock and close switch assembly connector.

  3. Check voltage between automatic back door lock and close switch assembly harness connector and ground.

    (+) (–)

    Voltage

    (Approx.)
    Automatic back door lock and close switch assembly
    Connector Terminal
    D513 9 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK AUTOMATIC BACK DOOR LOCK AND CLOSE SWITCH CIRCUIT

  1. Disconnect automatic back door control unit connector.

  2. Check continuity between automatic back door control unit harness connector and automatic back door lock and close switch assembly harness connector.

    Automatic back door control unit Automatic back door lock and close switch assembly Continuity
    Connector Terminal Connector Terminal
    B55 21 D513 9 Yes

  3. Check continuity between automatic back door control unit connector and ground.

    Automatic back door control unit — Continuity
    Connector Terminal
    B55 21 Ground No

Is the inspection result normal?

YES>>

Replace automatic back door control unit. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK AUTOMATIC BACK DOOR LOCK AND CLOSE SWITCH GROUND CIRCUIT

Check continuity between automatic back door lock and close switch assembly connector and ground.

Automatic back door lock and close switch assembly — Continuity
Connector Terminal
D513 12 Ground Yes

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness.

CHECK AUTOMATIC BACK DOOR LOCK AND CLOSE SWITCH

Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace automatic back door lock and close switch assembly. Refer to Removal and Installation.

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

>>

Inspection End.

Component Inspection

CHECK AUTOMATIC BACK DOOR LOCK AND CLOSE SWITCH

  1. Ignition switch OFF.

  2. Disconnect automatic back door lock and close switch connector.

  3. Check continuity between automatic back door lock and close switch terminals.

Automatic back door lock and close switch Condition Continuity
Terminal
9 12 Automatic back door lock and close switch Pressed Yes
Released No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace automatic back door lock and close switch assembly. Refer to Removal and Installation.

    Dtc/circuit Diagnosis. Automatic Back Door Switch
    Component Function Check CHECK FUNCTION CONSULT Ignition switch ON. Select “Automatic back door switch” in “Data monitor” mode of "AUTOMATIC BACK DOOR". Check that the f...
    Dtc/circuit Diagnosis. Back Door Switch
    Component Function Check CHECK FUNCTION CONSULT Ignition switch ON. Select “Back door/trunk lid switch” in “Data monitor” mode of "BCM [TRUNK]". Check that the function ...

    Other materials:

    2wd. Preparation. Preparation
    Preparation Special Service Tool Tool number (TechMate No.) Tool name Description KV40104000 ( – ) Hub lock nut wrench a: 85 mm (3.35 in) b: 65 mm (2.56 in) Removing and Installing wheel hub lock nut. KV40107300 ( – ) Boot band crimping tool Installing bo ...

    U2a8c-88 Ethernet Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detected condition U2A8C-88 Ethernet circuit Diagnosis condition When ignition switch is ON. Signal (terminal) — Threshold Lost ethernet communication with AV control unit Diagnosis delay time ...

    It Can Communication Circuit
    Diagnosis Procedure CHECK NETWORK DIAGNOSIS Check the "Network diagnosis" results from CONSULT to see that the diagnostic CAN communication circuit have no malfunction. Are the diagnostic CAN communication circuit normal? YES>> GO TO 2. NO>> Check and repair diagnostic CAN commu ...