Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Automatic Back Door Close Switch

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock / Dtc/circuit Diagnosis :: Automatic Back Door Close Switch

Component Function Check

CHECK FUNCTION

CONSULT

  1. Ignition switch ON.

  2. Select “Automatic back door close switch” in “Data monitor” mode of "AUTOMATIC BACK DOOR".

  3. Check that the function operates normally according to the following conditions.

Monitor item Condition Status
Automatic back door close switch Automatic back door close switch Pressed On
Released Off

Is the inspection result normal?

YES>>

Automatic back door close switch is OK.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK AUTOMATIC BACK DOOR CLOSE SWITCH INPUT SIGNAL

  1. Ignition switch OFF.

  2. Disconnect automatic back door lock and close switch assembly connector.

  3. Check voltage between automatic back door lock and close switch assembly harness connector and ground.

    (+) (–)

    Voltage

    (Approx.)
    Automatic back door lock and close switch assembly
    Connector Terminal
    D513 8 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK AUTOMATIC BACK DOOR CLOSE SWITCH CIRCUIT

  1. Disconnect automatic back door control unit connector.

  2. Check continuity between automatic back door control unit harness connector and automatic back door lock and close switch assembly harness connector.

    Automatic back door control unit Automatic back door lock and close switch assembly Continuity
    Connector Terminal Connector Terminal
    B55 3 D513 8 Yes

  3. Check continuity between automatic back door control unit harness connector and ground.

    Automatic back door control unit — Continuity
    Connector Terminal
    B55 3 Ground No

Is the inspection result normal?

YES>>

Replace automatic back door control unit. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK AUTOMATIC BACK DOOR CLOSE SWITCH GROUND CIRCUIT

Check continuity between automatic back door lock and close switch assembly harness connector and ground.

Automatic back door lock and close switch assembly — Continuity
Connector Terminal
D513 12 Ground Yes

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness.

CHECK AUTOMATIC BACK DOOR CLOSE SWITCH

Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace automatic back door lock and close switch assembly. Refer to Removal and Installation.

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

>>

Inspection End.

Component Inspection

CHECK AUTOMATIC BACK DOOR CLOSE SWITCH

  1. Ignition switch OFF.

  2. Disconnect automatic back door lock and close switch assembly connector.

  3. Check continuity between automatic back door lock and close switch assembly terminals.

Automatic back door lock and close switch assembly Condition Continuity
Terminal
8 12 Automatic back door close switch Pressed Yes
Released No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace automatic back door lock and close switch assembly. Refer to Removal and Installation.

    Dtc/circuit Diagnosis. U214e-87 Can Comm Circuit
    Intelligent Key Unit DTC Description DESCRIPTIONCAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Ariya vehicle multipl...
    Dtc/circuit Diagnosis. Automatic Back Door Serial Communication
    Diagnosis Procedure CHECK AUTOMATIC BACK DOOR SERIAL COMMUNICATION SIGNAL Ignition switch ON. Check signal between BCM harness connector and ground using oscilloscope. (+) (–)...

    Other materials:

    System Description. Component Parts. Moonroof System
    Moonroof System Component Description No. Component Function 1. Moonroof switch assembly Refer to Moonroof Switch Assembly. 2. Moonroof motor assembly Refer to Moonroof Motor Assembly. 3. Front door lock assembly RH (door switch) Detects door open/close condition ...

    Removal and Installation. 12v Battery Current Sensor
    Exploded View : 12V battery current sensor : Harness connector : N·m (kg-m, in-lb) Removal and Installation REMOVALDisconnect the 12V battery current sensor connector . Remove negative cable mounting nut , and then remove the negative cable . Loosen 12V battery cu ...

    P044c Egr Volume Control Valve Position Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P044C 00 EGR SENSOR C (EGR sensor C circuit low) Diagnosis condition Ignition switch ON Signal (terminal) EGR volume control valve signal Threshol ...