Nissan Rogue (T33) 2021-Present Service Manual: C1210-97 Ecm Signal

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detecting condition
C1210-97

ENGINE SIGNAL

(Engine signal)
Diagnosis condition
  • Ignition switch: ON

  • Engine running

Signal Torque down impossible signal
Threshold Detected the signal malfunction related protection for AWD system.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

The signal error related to AWD system protection

FAIL-SAFE

Although AWD control is canceled, the vehicle can drive at 2WD condition.

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE� has been previously conducted, always place ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

DTC REPRODUCTION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Drive at 10 km/h (6 MPH) or more for approximately 5 minutes in urban areas.

  3. Stop the Nissan Ariya vehicle.

  4. Perform "Self diagnosis result" mode of “AWD/4WD�.

Is DTC “C1210-97� detected?

YES>>

Proceed to diagnosis procedure. Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

PERFORM SELF DIAGNOSIS OF AWD CONTROL UNIT

CONSULT

  1. Erase "Self diagnosis result" mode of “AWD/4WD�.

  2. Start the engine, and wait for 15 seconds or more.

  3. Stop the engine.

  4. Perform "Self diagnosis result" mode of “AWD/4WD�.

Which DTC is detected?

C1210-97>>

GO TO 2.

Except C1210-97>>

Perform the trouble diagnosis for detected DTC. Refer to DTC Index.

No DTC>>

Inspection End.

PERFORM SELF DIAGNOSIS OF ECM

CONSULT

Perform "Self diagnosis result" mode of “ECM�.

Is any DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 3.

PERFORM SELF DIAGNOSIS OF TCM

CONSULT

Perform "Self diagnosis result" mode of “TRANSMISSION�.

Is any DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 4.

CHECK TERMINALS AND HARNESS CONNECTORS

Check AWD control unit pin terminals for damage or loose connection with harness connector.

Is inspection result normal?

YES>>

After placing the ignition switch OFF, perform DTC confirmation procedure again. If DTC “C1210-97� is detected, replace actuator assembly due to the malfunction of the AWD control unit. Refer to Disassembly and Assembly.

NO>>

Repair or replace error-detected parts.

    C1203-86 Abs Signal
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detecting condition C1203-86 ABS SYSTEM (Antilock brake system) Diagnosis condition ...
    C1213-A2 Control Unit Power Supply
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detecting condition C1213-A2 BATTERY VOLTAGE (Battery voltage) Diagnosis condition I...

    Other materials:

    Manual Air Conditioning. Precaution. Precautions
    Precautions Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as “AIR BAG� and “SEAT BELT PRE-TENSIONER�, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and ...

    Ecu Diagnosis Information. Electrically-Driven Intelligent Brake Unit
    DTC Index DTC Display item Brake warning lamp Brake system warning lamp Refer to B14E0-02 Wheel sensor OFF ON DTC Description B14E0-09 Wheel sensor OFF ON DTC Description B14E0-11 Wheel sensor OFF ON DTC Description B14E0-12 Wheel sensor ...

    With Idle Start/stop. System Description
    Component Parts Component Parts Location No. Component Function 1. Sub starter & generator Refer to Sub starter & generator. 2. Battery current sensor (with battery temperature sensor) Refer to 12V Battery Current Sensor . 3. ECM (Engine Control Module The ...