Nissan Rogue (T33) 2021-Present Service Manual: C1061-64 Wheel Sensor Fl

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake Control System / With Vdc :: Dtc/circuit Diagnosis / C1061-64 Wheel Sensor Fl

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C1061 64

Wheel sensor FL

(Wheel sensor front left) 		Diagnosis condition

  • When ignition switch is ON.

  • When front left wheel sensor power supply voltage is normal.

  • When the Nissan Ariya vehicle speed is 10 km/h (6.2 MPH) – 60 km/h (37 MPH).
Signal (terminal) Front left wheel sensor signal
Threshold When difference between front left wheel and other front left wheel speed is detected the Nissan Ariya vehicle is driven, because of installation of other tires than specified.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

NOTE:

Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.

PAST DTC CRNT DTC

  • Harness or connector

  • Front left wheel sensor

  • Front left sensor rotor

  • Front left tire size

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

  • Nissan Ariya Vehicle was not driven after previous repair

  • Harness or connector

  • Front left wheel sensor

  • Front left sensor rotor

  • Front left tire size

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

FAIL-SAFE

The following functions are suspended.

  • VDC function

  • TCS function

  • ABS function

  • EBD function

  • Brake limited slip differential (BLSD) function

  • Brake assist function

  • Brake force distribution function

  • hill start assist function

  • Electric parking brake function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Start the engine.

  2. Drive the Nissan Ariya vehicle at approximately 50 km/h (31 MPH) or more for approximately 2 minutes.

  3. Stop the vehicle.

  4. Ignition switch OFF (Auto ACC function OFF).

  5. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  6. Perform self-diagnosis for “ABS”.

Is DTC “C1061-64” detected?

YES-1>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES-2>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CAUTION:

Never check between wheel sensor harness connector terminals.

CHECK WHEEL HUB ASSEMBLY

  1. Disconnect 12V battery negative terminal.

  2. Check that there is no excessive looseness in front left wheel hub assembly.

    • FWD models: Refer to Inspection.

    • AWD models: Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace the front left wheel hub assembly. GO TO 2.

  • FWD models: Refer to Removal and Installation.

  • AWD models: Refer to Removal and Installation.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link.

CHECK TIRE

Check the front left tire air pressure, wear and size. Refer to Tire Air Pressure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Adjust air pressure or replace front left tire. GO TO 4.

CHECK DATA MONITOR (1)

CONSULT

  1. Connect 12V battery negative terminal.

  2. Erase self-diagnosis result for “ABS”.

  3. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  4. Start the engine.

  5. Select “ABS” and “Data Monitor”, check "FR LH wheel speed", "FR RH wheel speed", "RR LH wheel speed", and "RR RH wheel speed".

    NOTE:

    Set the “Data Monitor” recording speed to “10 msec”.

  6. Read a value (wheel speed) of all wheel sensor.

    NOTE:

    Nissan Ariya Vehicle must be driven after repair or replacement to erase the previous DTCs.

Note the difference at 50 km/h (31 MPH) between the wheel speed detected by front left wheel sensor and the maximum/minimum wheel speed detected by the other front left wheel sensor, is the difference within 5%, respectively?

YES>>

GO TO 5.

NO>>

GO TO 6.

PERFORM SELF-DIAGNOSIS (1)

CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Ignition switch OFF (Auto ACC function OFF).

  3. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  4. Perform self-diagnosis for “ABS”.

Is DTC “C1061-64” detected?

YES>>

GO TO 6.

NO>>

Inspection End

CHECK WHEEL SENSOR AND SENSOR ROTOR

  1. Disconnect 12V battery negative terminal.

  2. Disconnect front left wheel sensor harness connector.

  3. Remove dust and foreign matter adhered to the front left wheel sensor and front left sensor rotor with a vacuum dust collector through the front left wheel sensor mounting hole.

    CAUTION:

    Install wheel sensor with no backlash and float, and tighten the mounting bolt to the specified torque. Refer to Exploded View.

>>

GO TO 7.

CHECK WHEEL SENSOR

Check the front left wheel sensor for damage.

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

GO TO 8.

CHECK WHEEL SENSOR OUTPUT SIGNAL

  1. Disconnect ABS actuator and electric unit (control unit) harness connector.

  2. Disconnect front left wheel sensor harness connector.

  3. Connect ABS active wheel sensor tester (SST: NI-45741) to front left wheel sensor using appropriate adapter.

  4. Turn the ABS active wheel sensor tester power switch ON.

    NOTE:

    The green POWER indicator should illuminate. If the POWER indicator does not illuminate, replace the battery in the ABS active wheel sensor tester before proceeding.

  5. Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.

    NOTE:

    If the red SENSOR indicator illuminates but does not flash, reverse the polarity of the tester leads and retest.

Does the ABS active wheel sensor tester detect a signal?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

GO TO 9.

REPLACE WHEEL SENSOR (1)

CONSULT

  1. Replace the front left wheel sensor. Refer to Removal and Installation.

  2. Connect 12V battery negative terminal.

  3. Erase self-diagnosis result for “ABS”.

  4. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  5. Start the engine.

  6. Select “ABS” and “Data Monitor”, check "FR LH wheel speed", "FR RH wheel speed", "RR LH wheel speed", and "RR RH wheel speed".

    NOTE:

    Set the “Data Monitor” recording speed to “10 msec”.

  7. Read a value (wheel speed) of all wheel sensor.

    NOTE:

    Nissan Ariya Vehicle must be driven after repair or replacement to erase the previous DTCs.

Note the difference at 50 km/h (31 MPH) between the wheel speed detected by front left wheel sensor and the maximum/minimum wheel speed detected by the other front left wheel sensor, is the difference within 5%, respectively?

YES>>

GO TO 10.

NO>>

GO TO 22.

PERFORM SELF-DIAGNOSIS (2)

CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Ignition switch OFF (Auto ACC function OFF).

  3. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  4. Perform self-diagnosis for “ABS”.

Is DTC “C1061-64” detected?

YES>>

GO TO 22.

NO>>

Inspection End

CHECK CONNECTOR

  1. Disconnect 12V battery negative terminal.

  2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.

  3. Check the front left wheel sensor harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 14.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 12.

CHECK DATA MONITOR (2)

CONSULT

  1. Connect 12V battery negative terminal.

  2. Erase self-diagnosis result for “ABS”.

  3. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  4. Start the engine.

  5. Select “ABS” and “Data Monitor”, check "FR LH wheel speed", "FR RH wheel speed", "RR LH wheel speed", and "RR RH wheel speed".

    NOTE:

    Set the “Data Monitor” recording speed to “10 msec”.

  6. Read a value (wheel speed) of all wheel sensor.

    NOTE:

    Nissan Ariya Vehicle must be driven after repair or replacement to erase the previous DTCs.

Note the difference at 50 km/h (31 MPH) between the wheel speed detected by front left wheel sensor and the maximum/minimum wheel speed detected by the other front left wheel sensor, is the difference within 5%, respectively?

YES>>

GO TO 13.

NO>>

GO TO 14.

PERFORM SELF-DIAGNOSIS (3)

CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Ignition switch OFF (Auto ACC function OFF).

  3. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  4. Perform self-diagnosis for “ABS”.

Is DTC “C1061-64” detected?

YES>>

GO TO 14.

NO>>

Inspection End

CHECK TERMINAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect ABS actuator and electric unit (control unit) harness connector and then check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.

  3. Disconnect front left wheel sensor harness connector and check the front left wheel sensor terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 17.

NO>>

Repair / replace harness, connector, or terminal. GO TO 15.

CHECK DATA MONITOR (3)

CONSULT

  1. Connect ABS actuator and electric unit (control unit) harness connector.

  2. Connect front left wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Erase self-diagnosis result for “ABS”.

  5. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  6. Start the engine.

  7. Select “ABS” and “Data Monitor”, check "FR LH wheel speed", "FR RH wheel speed", "RR LH wheel speed", and "RR RH wheel speed".

    NOTE:

    Set the “Data Monitor” recording speed to “10 msec”.

  8. Read a value (wheel speed) of all wheel sensor.

    NOTE:

    Nissan Ariya Vehicle must be driven after repair or replacement to erase the previous DTCs.

Note the difference at 50 km/h (31 MPH) between the wheel speed detected by front left wheel sensor and the maximum/minimum wheel speed detected by the other front left wheel sensor, is the difference within 5%, respectively?

YES>>

GO TO 16.

NO>>

GO TO 17.

PERFORM SELF-DIAGNOSIS (4)

CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Ignition switch OFF (Auto ACC function OFF).

  3. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  4. Perform self-diagnosis for “ABS”.

Is DTC “C1061-64” detected?

YES>>

GO TO 17.

NO>>

Inspection End

CHECK WHEEL SENSOR HARNESS

  1. Disconnect 12V battery negative terminal.

  2. Disconnect ABS actuator and electric unit (control unit) harness connector.

  3. Disconnect front left wheel sensor harness connector.

  4. Check the continuity between ABS actuator and electric unit (control unit) harness connector and the ground.

    ABS actuator and electric unit (control unit) — Continuity
    Connector Terminal
    E125 24, 7 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 18.

NO>>

Repair / replace harness or connector. GO TO 18.

CHECK DATA MONITOR (4)

CONSULT

  1. Connect ABS actuator and electric unit (control unit) harness connector.

  2. Connect front left wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Erase self-diagnosis result for “ABS”.

  5. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  6. Start the engine.

  7. Select “ABS” and “Data Monitor”, check "FR LH wheel speed", "FR RH wheel speed", "RR LH wheel speed", and "RR RH wheel speed".

    NOTE:

    Set the “Data Monitor” recording speed to “10 msec”.

  8. Read a value (wheel speed) of all wheel sensor.

    NOTE:

    Nissan Ariya Vehicle must be driven after repair or replacement to erase the previous DTCs.

Note the difference at 50 km/h (31 MPH) between the wheel speed detected by front left wheel sensor and the maximum/minimum wheel speed detected by the other front left wheel sensor, is the difference within 5%, respectively?

YES>>

GO TO 19 .

NO>>

GO TO 20.

PERFORM SELF-DIAGNOSIS (5)

CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Ignition switch OFF (Auto ACC function OFF).

  3. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  4. Perform self-diagnosis for “ABS”.

Is DTC “C1061-64” detected?

YES>>

GO TO 20.

NO>>

Inspection End

REPLACE WHEEL SENSOR (2)

CONSULT

  1. Disconnect 12V battery negative terminal.

  2. Replace the front left wheel sensor. Refer to Removal and Installation.

  3. Connect 12V battery negative terminal.

  4. Erase self-diagnosis result for “ABS”.

  5. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  6. Start the engine.

  7. Select “ABS” and “Data Monitor”, check "FR LH wheel speed", "FR RH wheel speed", "RR LH wheel speed", and "RR RH wheel speed".

    NOTE:

    Set the “Data Monitor” recording speed to “10 msec”.

  8. Read a value (wheel speed) of all wheel sensor.

    NOTE:

    Nissan Ariya Vehicle must be driven after repair or replacement to erase the previous DTCs.

Note the difference at 50 km/h (31 MPH) between the wheel speed detected by front left wheel sensor and the maximum/minimum wheel speed detected by the other front left wheel sensor, is the difference within 5%, respectively?

YES>>

GO TO 21.

NO>>

GO TO 22.

PERFORM SELF-DIAGNOSIS (6)

CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Ignition switch OFF (Auto ACC function OFF).

  3. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  4. Perform self-diagnosis for “ABS”.

Is DTC “C1061-64” detected?

YES>>

GO TO 22.

NO>>

Inspection End

REPLACE SENSOR ROTOR

CONSULT

  1. Disconnect 12V battery negative terminal.

  2. Replace the front left sensor rotor.

    • FWD models: Refer to Removal and Installation.

    • AWD models: Refer to Removal and Installation.

  3. Connect 12V battery negative terminal.

  4. Erase self-diagnosis result for “ABS”.

  5. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  6. Start the engine.

  7. Drive the Nissan Ariya vehicle at approximately 50 km/h (31 MPH) or more for approximately 2 minutes.

    NOTE:

    Nissan Ariya Vehicle must be driven after repair or replacement to erase the previous DTCs.

  8. Stop the Nissan Ariya vehicle.

  9. Ignition switch OFF (Auto ACC function OFF).

  10. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  11. Perform self-diagnosis for “ABS”.

Is DTC “C1061-64” detected?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Inspection End

    C1061-4a Wheel Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1061 4A FR LH wheel sensor (Front left wheel sensor) Diagno...
    C1061-92 Wheel Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1061 92 Wheel sensor FL (Wheel sensor front left) Diagnosis...

    Other materials:

    Automatic air conditioner (models without rear control)
    Models with heated steering wheel Models without heated steering wheel Basic information Temperature control dial (driver's side) AUTO button Display screen SYNC button Temperature control dial (passenger's side) ON·OFF button Air recirculation button Fan speed buttons Air flow ...

    Dtc/circuit Diagnosis. B100e-1a Knee Air Bag Module Rh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B100E-1A Knee air bag module RH (Knee air bag module right hand) Diagnosis condition When ignition switch is ON. Signal (terminal) Knee air bag module RH si ...

    Power Supply and Ground Circuit
    8ch Can Gateway Diagnosis Procedure CHECK FUSE Check that the following fuse are not blown. Signal name Fuse No. Battery power supply 16 Ignition power supply 9 Is the fuse blown (open)? YES>> Replace the blown fuse after repairing the affected circuit if a fuse ...