Nissan Rogue (T33) 2021-Present Service Manual: C1058-92 Control Unit
DTC Description
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | |||
|---|---|---|---|---|---|
| C1058 | 92 |
Control unit (Control unit) |
Diagnosis condition |
|
|
| Signal (terminal) | - | ||||
| Threshold | When there is an internal malfunction in the ABS actuator and electric unit (control unit). | ||||
| Diagnosis delay time | 2 seconds or less | ||||
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
-
VDC function
-
TCS function
-
ABS function
-
EBD function
-
Brake limited slip differential (BLSD) function
-
Brake assist function
-
Brake force distribution function
-
hill start assist function
-
Electric parking brake function
DTC CONFIRMATION PROCEDURE
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.
>>
GO TO 2.
CHECK DTC DETECTION
CONSULT
-
Ignition switch OFF (Auto ACC function OFF).
-
Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
-
Perform self-diagnosis for “ABS”.
Is DTC “C1058-92” detected?
YES-1>>“CRNT” is displayed: Refer to Diagnosis Procedure.
YES-2>>“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: Inspection End
Diagnosis Procedure
ADJUST THE NEUTRAL POSITION OF STEERING ANGLE SENSOR
-
Perform neutral position adjustment of steering angle sensor. Refer to Work Procedure.
-
Perform “All DTC Reading”.
Is DTC detected?
YES>>Check the DTC.
NO>>GO TO 2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair / replace harness, connector, terminal, fuse, or fusible link.
PERFORM SELF-DIAGNOSIS
CONSULT
Perform self-diagnosis for “ABS”.
NOTE:
Replace the ABS actuator and electric unit (control unit) even if other DTCs are displayed along with “C1058-92” in self-diagnosis for “ABS”.
Is DTC “C1058-92” detected?
YES>>Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
NO>>Inspection End [Although motor built in the ABS actuator and electric unit (control unit) operates temporarily without a break, this is not a malfunction. Erase the all memory of self-diagnosis results.]
Other materials:
B2721-11 Center Sensor [rl]
DTC Description
DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition
B2721-11
CENTER SENSOR [RL]
(Center sensor [RL])
Diagnosis condition
When ignition switch is ON
Signal (terminal)
Rear sonar sensor signal LH inner
Threshold ...
P00d2 Ho2s2 Heater
DTC Description
DTC DETECTION LOGIC DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
P00D2
00
Heated O2 sensor heater B1 sensor 2
(HO2S heater control circuit range/performance bank 1 sensor 2)
Diagnosis condition
—
Signal (terminal)
...
Reporting safety defects
For USA
If you believe that your vehicle has a defect that could cause a crash or lead to injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying NISSAN. This applies whether you drive a Nissan Rogue or another NISSAN model.
...