Nissan Rogue (T33) 2021-Present Service Manual: C1058-49 Control Unit

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake Control System / With Vdc :: Dtc/circuit Diagnosis / C1058-49 Control Unit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C1058 49

Control unit

(Control unit) 		Diagnosis condition

  • When ignition switch is ON.

  • When the power supply voltage is normal.
Signal (terminal) -
Threshold When there is an internal malfunction in the ABS actuator and electric unit (control unit).
Diagnosis delay time 2 seconds or less

POSSIBLE CAUSE

NOTE:

Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.

PAST DTC CRNT DTC

  • The Nissan Ariya vehicle travels near high-voltage electrical power lines.

  • Motor built in the ABS actuator and electric unit (control unit) operates temporarily without a break.

  • Harness or connector

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

  • Incomplete adjustment of steering angle sensor neutral position.

  • Harness or connector

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

FAIL-SAFE

The following functions are suspended.

  • VDC function

  • TCS function

  • ABS function

  • EBD function

  • Brake limited slip differential (BLSD) function

  • Brake assist function

  • Brake force distribution function

  • hill start assist function

  • Electric parking brake function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C1058-49” detected?

YES-1>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES-2>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

ADJUST THE NEUTRAL POSITION OF STEERING ANGLE SENSOR

  1. Perform neutral position adjustment of steering angle sensor. Refer to Work Procedure.

  2. Perform “All DTC Reading”.

Is DTC detected?

YES>>

Check the DTC.

NO>>

GO TO 2.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link.

PERFORM SELF-DIAGNOSIS

CONSULT

Perform self-diagnosis for “ABS”.

NOTE:

Replace the ABS actuator and electric unit (control unit) even if other DTCs are displayed along with “C1058-49” in self-diagnosis for “ABS”.

Is DTC “C1058-49” detected?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Inspection End [Although motor built in the ABS actuator and electric unit (control unit) operates temporarily without a break, this is not a malfunction. Erase the all memory of self-diagnosis results.]

    C1058-44 Control Unit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1058 44 Control unit (Control unit) Diagnosis condition Whe...
    C1058-51 Control Unit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1058 51 Control unit (Control unit) Diagnosis condition Whe...

    Other materials:

    Heated steering wheel
    Example Push the heated steering wheel switch to warm the steering wheel after the engine starts. The indicator light A will illuminate once the system is active. If the steering wheel surface temperature is below 86–104ºF (30–40ºC), the system will automatically heat the wheel and cycle o ...

    Removal and Installation. Tire Pressure Sensor
    Exploded View Screw Tire pressure sensor Valve Valve core Valve cap : Comply with the assembly procedure when tightening. Refer to Removal and Installation. : N·m (kg-m, in-lb) : Always replace after every disassembly. Removal & Install ...

    C1f41-84 Cvt
    Without Propilot Assist 2.1 DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition   C1F41 84 TRANSMISSION CIRCUIT (Transmission circuit) Diagnosis condition When engine is running When AEB system is O ...