Nissan Rogue (T33) 2021-Present Service Manual: B272b-88 Center Sensor [fr]

Nissan Rogue (T33) 2021-Present Service Manual / Driver Information & Multimedia :: Sonar System / Dtc/circuit Diagnosis :: Sonar (sonar Control Unit) / B272b-88 Center Sensor [fr]

DTC Description

DTC DETECTION LOGIC

DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition
B272B-88

CENTER SENSOR [FR]

(Center sensor [FR]) 		Diagnosis condition When ignition switch is ON
Signal (terminal) —
Threshold Communication error
Diagnosis delay time 4 seconds or more

POSSIBLE CAUSE

  • Harness and connector between sonar control unit and front sonar sensor RH inner

  • Front sonar sensor RH inner

FAIL-SAFE

Stop the obstacle detection function

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Turn ignition switch ON.

  2. Turn ignition switch OFF and wait at least 30 seconds.

  3. Turn ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “SONAR” using CONSULT.

  5. Check the DTC.

Is DTC “B272B–88” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK FRONT SONAR SENSOR SIGNAL RH INNER CIRCUIT (1)

  1. Turn ignition switch OFF.

  2. Disconnect sonar control unit connector and front sonar sensor RH inner connector.

  3. Turn ignition switch ON.

  4. Check voltage between sonar control unit harness connector and ground.

    Sonar control unit (-) Voltage (Approx. )
    Connector Terminal
    B20 1 Ground 0 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair harness or connector.

CHECK FRONT SONAR SENSOR SIGNAL RH INNER CIRCUIT (2)

  1. Turn ignition switch OFF.

  2. Check continuity between front sonar sensor RH inner harness connector and ground.

Front sonar sensor RH inner Ground Continuity
Connector Terminal
E306 2 Not existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the harness or connector.

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

With CONSULT

  1. Connect sonar control unit connector and front sonar sensor RH inner connector.

  2. Turn ignition switch ON.

  3. Erase DTC.

  4. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC B272B-88 detected again?

YES>>

Replace the front sonar sensor RH inner. Refer to Removal and Installation.

NO>>

INSPECTION END

    B272b-83 Center Sensor [fr]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B272B-83 CENTER SENSOR [FR] (Center sensor [FR]) Diagnosis condi...
    B272b-92 Center Sensor [fr]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B272B-92 CENTER SENSOR [FR] (Center sensor [FR]) Diagnosis condi...

    Other materials:

    U216e-87 Can Comm Circuit
    DTC Description CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Ariya vehicle multiplex communication system with high data communication speed and excellent error detectability. Many electronic control units are equipped onto Nis ...

    B24a4-11 Intake Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B24A4-11 INTAKE SENSOR (Intake sensor) Diagnosis condition Ignition switch ON Signal (Terminal) Intake sensor signal Threshold The intake sensor rec ...

    Automatic air conditioner (models without rear control)
    Models with heated steering wheel Models without heated steering wheel Basic information Temperature control dial (driver's side) AUTO button Display screen SYNC button Temperature control dial (passenger's side) ON·OFF button Air recirculation button Fan speed buttons Air flow ...