Nissan Rogue (T33) 2021-Present Service Manual: B20de-72 Ign Relay Off Circ

Nissan Rogue (T33) 2021-Present Service Manual / Electrical & Power Control :: Power Control System / Ipdm E/r :: Dtc/circuit Diagnosis / B20de-72 Ign Relay Off Circ

DTC Description

  • IPDM E/R operates the ignition relay when it receives an ignition ON signal from BCM via CAN communication.

  • Turn the ignition relay OFF by pressing the push-button ignition switch once when the Nissan Ariya vehicle speed is 2.5 MPH (4 km/h) or less.

  • Turn the ignition relay OFF with the following operation when the Nissan Ariya vehicle speed is more than 2.5 MPH (4 km/h) or when an abnormal condition occurs in CAN communication from the ABS actuator and electric unit (control unit) (emergency OFF):

    • Press and hold the push-button ignition switch for 2 seconds or more.

    • Press the push-button ignition switch 3 times within 1.5 seconds.

NOTE:

The ignition relay does not turn ON for 3 seconds after emergency OFF even if the push-button ignition switch is pressed.

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC detection condition
B20DE-72

IGN RELAY OFF CIRC

(Ignition relay OFF circuit) 		[ACTUATOR STUCK OPEN] Diagnosis condition When ignition switch is ON
Signal (terminal) CPU monitors the status at the contact and excitation coil circuits of the ignition relay inside it
Threshold The ignition relay OFF is detected
Diagnosis delay time 1 second or more

POSSIBLE CAUSE

IPDM E/R

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select “Self diagnosis result” mode of “IPDM E/R”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

REPLACE IPDM E/R

Replace IPDM E/R. Refer to Removal and Installation.

>>

Inspection End.

    B20dd-73 Ign Relay on Circ
    DTC Description IPDM E/R operates the ignition relay when it receives an ignition ON signal from BCM via CAN communication. Turn the ignition relay OFF by pressing the push-butt...
    U0073-00 Control Module Comm Bus a Off
    DTC Description CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Ariya vehicle multiplex communication line with high ...

    Other materials:

    C1f59-04 Eps Circuit
    Without Propilot Assist 2.1 DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition   C1F59 04 EPS control unit (Electric power steering control unit) Diagnosis condition When engine is running Signal (termi ...

    Dtc/circuit Diagnosis. U0075-00 Communication Bus C Off
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition U0075-00 Control module comm Bus C Off (Control module communication Bus C Off) Diagnosis condition Ignition switch ON Signal (terminal) CAN communication s ...

    Dtc/circuit Diagnosis. B0010-11 Assist A/b Module
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B0010-11 ASSIST A/B MODULE (Passenger Frontal Stage 1 Deployment Control) Diagnosis condition When ignition switch is ON. Signal (terminal) Passenger air ba ...