Nissan Rogue manuals

Nissan Rogue Service Manual: B0093 front door satellite sensor LH

DTC Logic

DTC DETECTION LOGIC

With CONSULT

CONSULT name

DTC

DTC detecting condition

Repair order

DOOR SATELLITE SENSOR LH [SENSOR FAIL] B0093 Front door satellite sensor LH has malfunctioned. Refer to SRC-70, "Diagnosis Procedure".
DOOR SATELLITE SENSOR LH [COMM FAIL] Front door satellite sensor LH communication error.
DOOR SATELLITE SENSOR LH [DISCONNECT] Front door satellite sensor LH is disconnected.
DOOR SATELLITE SENSOR LH [UNMATCH] Front door satellite sensor LH is out of specification.
DOOR SATELLITE SENSOR LH [GND-SHORT] Front door satellite sensor LH circuit is shorted to ground.

DTC CONFIRMATION PROCEDURE (With CONSULT)

1.CHECK SELF-DIAG RESULT

  1.  Turn ignition switch ON.
  2.  Check for DTC using CONSULT.

Is the DTC detected? YES (Current DTC)>>Refer to SRC-70, "Diagnosis Procedure".

YES (Past DTC)>>GO TO 2.

NO >> Inspection End.

2.ERASE SELF-DIAG RESULT

Erase the DTC using CONSULT.

Can the DTC be erased? YES >> Inspection End.

NO >> Refer to SRC-70, "Diagnosis Procedure".

DTC CONFIRMATION PROCEDURE (Without CONSULT)

1.CHECK SELF-DIAG RESULT

  1.  Turn ignition switch ON.
  2.  Check the air bag warning lamp status. Refer to SRC-16, "On Board Diagnosis Function".

NOTE: SRS will not enter diagnosis mode if no malfunction is detected in user mode. Is the DTC detected? YES >> Refer to SRC-70, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

Recheck SRS after each replacement.

1.HARNESS CONNECTOR

NOTE: All harness connectors should be inspected from the air bag diagnosis sensor unit to the end component (including any in-line connectors).

Is the inspection result normal? YES >> GO TO 2.

NO >> Perform one of the following repairs:

2.CONFIRM DTC

  1.  Reconnect all harness connectors.
  2.  Turn ignition switch ON.
  3.  Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 3.

NO >> Refer to GI-41, "Intermittent Incident".

3.WIRING HARNESS

Check the wiring harness for visible damage.

NOTE: The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component (including any in-line connectors). Is the inspection result normal? YES >> GO TO 4.

NO >> Replace the harness.

4.CONFIRM DTC

  1.  Reconnect all harness connectors.
  2.  Turn ignition switch ON.
  3.  Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 5.

NO >> Refer to GI-41, "Intermittent Incident".

5.FRONT DOOR SATELLITE SENSOR LH

  1.  Replace the front door satellite sensor LH. Refer to SR-24, "Removal and Installation".
  2.  Turn ignition switch ON.
  3.  Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 6.

NO >> Clear DTC. Inspection End.

6.AIR BAG DIAGNOSIS SENSOR UNIT

  1.  Replace the air bag diagnosis sensor unit. Refer to SR-26, "Removal and Installation".
  2.  Turn ignition switch ON.
  3.  Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 7.

NO >> Clear DTC. Inspection End.

7.RELATED HARNESS

Replace the related harness.

>> END

B0094 crash zone sensor
DTC Logic DTC DETECTION LOGIC CONSULT name DTC DTC detecting condition Repair order CRASH ZONE SENSOR [SENSOR FAIL] B0094 Crash zone sensor has malf ...

B0098 front door satellite sensor RH
DTC Logic DTC DETECTION LOGIC With CONSULT CONSULT name DTC DTC detecting condition Repair order DOOR SATELLITE SENSOR RH [SENSOR FAIL] B0098 Front ...

Other materials:

Doors
When the doors are locked using one of the following methods, the doors cannot be opened using the inside or outside door handles. The doors must be unlocked to open the doors. WARNING  Always have the doors locked while driving. Along with the use of seat belts, this pro ...

System
System Description SYSTEM DIAGRAM POWER WINDOW OPERATION Main power window and door lock/unlock switch can open/close all windows.  Front and rear power window switches can open/close the corresponding windows. POWER WINDOW AUTO-OPERATION (FRONT DRIVER SIDE) AUTO UP/DOW ...

Meter control switch signal circuit
Diagnosis Procedure Regarding Wiring Diagram information, refer to MWI-32, "Wiring Diagram". 1.CHECK METER CONTROL SWITCH SIGNAL  Turn ignition switch ON.  Check voltage between the following terminals of the meter control switch harness connector M3. Is the ins ...

В© 2014-2025 Copyright www.nirogue.com