Nissan Rogue (T33) 2021-Present Service Manual: Automatic Brake Hold :: Basic Inspection. Diagnosis and Repair Work Flow

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake Control System / Automatic Brake Hold :: Basic Inspection. Diagnosis and Repair Work Flow

Diagnosis and Repair Work Flow

Work Flow

DETAILED FLOW

INTERVIEW FROM THE CUSTOMER

Clarify customer complaints before inspection. First of all, perform an interview utilizing Diagnostic Work Sheet and reproduce the symptom as well as fully understand it. Ask customer about his/her complaints carefully. Check symptoms by driving Nissan Ariya vehicle with customer, if necessary.

CAUTION:

Customers are not professional. Never guess easily like “maybe the customer means that...,” or “maybe the customer mentions this symptom”.

>>

GO TO 2.

CHECK SYMPTOM

Reproduce the symptom that is indicated by the customer, based on the information from the customer obtained by the interview. Also check that the symptom is not caused by fail-safe mode. Refer to Fail-safe.

CAUTION:

When the symptom is caused by normal operation, fully inspect each portion and obtain the understanding of customer that the symptom is not caused by a malfunction.

>>

GO TO 3.

PERFORM SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC detected?

YES>>

Record or print self-diagnosis results and freeze frame data (FFD). GO TO 4.

NO>>

INSPECTION END

PERFORM DTC DIAGNOSIS PROCEDURE

With CONSULT

Perform DTC confirmation procedures for the error-detected system.

NOTE:

If some DTCs are detected at the same time, determine the order for performing the diagnosis.

  • Without telematics system: Refer to DTC Inspection Priority Chart.

  • With telematics system: Refer to DTC Inspection Priority Chart.

Is DTC detected?

YES>>

GO TO 5.

NO>>

Check harness and connectors based on the information obtained by the interview.

REPAIR OR REPLACE ERROR-DETECTED PARTS

  1. Repair or replace error-detected parts.

  2. Reconnect part or connector after repairing or replacing.

  3. When DTC is detected, erase self-diagnosis results for “CHASSIS CONTROL”.

>>

GO TO 6.

FINAL CHECK

With CONSULT

  1. Check the reference value for “CHASSIS CONTROL”.

  2. Recheck the symptom and check that the symptom is not reproduced on the same conditions.

Is the symptom reproduced?

YES>>

GO TO 3.

NO>>

INSPECTION END

Diagnostic Work Sheet

Description

  • In general, customers have their own criteria for a symptom. Therefore, it is important to understand the symptom and status well enough by interviewing the customer about the symptom carefully. To systemize all the information for the diagnosis, prepare the interview sheet referring to the interview points.

  • In some cases, multiple conditions that appear simultaneously may cause a DTC to be detected.

INTERVIEW SHEET SAMPLE

Interview sheet
Customer name MR/MS Registration number Initial year registration
Nissan Ariya Vehicle type VIN
Storage date Engine / Traction motor Mileage km ( Mile)
Symptom □ Does not operate ( ) function
□ Warning lamp for ( ) turns ON.
□ Noise                 □ Vibration

□ Other

( )
First occurrence □ Recently □ Other ( )
Frequency of occurrence □ Always □ Under a certain conditions of □ Sometimes ( time(s)/day)
Climate conditions □ Irrelevant
Weather □ Fine □ Cloud □ Rain □Snow □ Others ( )
Temperature □ Hot □Warm □ Cool □ Cold □ Temperature [Approx. °C ( °F)]
Relative humidity □ High □ Moderate □ Low
Road conditions

□ Urban area □ Suburb area □ Highway

□ Mountainous road (uphill or downhill) □ Rough road
Operating condition, etc.

□Irrelevant

□When traction motor starts □ During idling

□ During driving □ During acceleration □ At constant speed driving

□ During deceleration

□ During cornering (right curve or left curve)

□ When steering wheel is steered (to right or to left)
Other conditions

Nissan Ariya Vehicle equipment

Memo
    Automatic Brake Hold. Wiring Diagram
    Chassis Control System - With Propilot Assist 2.1 Wiring Diagram Refer to Wiring Diagram. Chassis Control System - Without Propilot Assist 2.1 Wiring Diagram Refer to Wiring Dia...
    Automatic Brake Hold. Dtc/circuit Diagnosis
    Automatic Brake Hold Switch Component Function Check NOTE: Parking brake switch and automatic brake hold switch are single unit. (Indicator is integrated with switch.) CHECK AUT...

    Other materials:

    P26a3 Multi-Way Control Valve Motor
    DTC Description DTC DETECTION LOGICNOTE: If DTC P26A3 is displayed with DTC P26A5, P26A6, and/or P26A7 first perform the trouble diagnosis for DTC P26A5, P26A6, and/or P26A7. Refer to DTC Index. DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P26A3 00 ...

    Intelligent Around View Monitor. Preparation. Preparation
    Preparation Special Service Tools The actual shape of the tools may differ from those illustrated here. Tool number (TechMate No.) Tool name Description - (NI-53373) ADAS calibration laser level Target setup and ADAS calibration - (NI-53371) ADAS calibration rod ...

    Egr Temperature Sensor
    Component Inspection CHECK EGR TEMPERATURE SENSOR Turn ignition switch OFF. Disconnect EGR temperature sensor harness connector. Remove EGR temperature sensor. Check resistance between EGR temperature sensor terminals. EGR temperature sensor Condition Resistance  + − ...