Nissan Rogue (T33) 2021-Present Service Manual: U2e65-57 Mac Comm Error (sonar Control Unit)

Nissan Rogue (T33) 2021-Present Service Manual / Cruise Control & Driver Assistance :: Driver Assistance System / Chassis Control :: Dtc/circuit Diagnosis / U2e65-57 Mac Comm Error (sonar Control Unit)

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
U2E65 57 CAN communication error (sonar control unit) Diagnosis condition —
Signal (terminal) —
Threshold MAC communication error.
Diagnosis delay time —

POSSIBLE CAUSE

  • Chassis control module used in vehicles is installed in the vehicle

  • Chassis control module

  • Sonar control unit

FAIL-SAFE

Normal control

DTC CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “U2E65-57” is displayed with DTC “U1327-52” or “U1327-54”, first perform the trouble diagnosis for DTC “U1327-52” or “U1327-54”.

Is DTC “U1327-52” or “U1327-54” detected?

YES>>

  • “U1327–52”: Refer to DTC Description.

  • “U1327–54”: Refer to DTC Description.

NO>>

GO TO 2.

CHECK MAC DIAGNOSIS

With CONSULT

  1. Ignition switch ON.

  2. Perform “MAC Diagnosis” mode of “CHASSIS CONTROL” using CONSULT.

Is DTC “U2E65-57” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “U2E65-57” is displayed with DTC “U1327-52” or “U1327-54”, first perform the trouble diagnosis for DTC “U1327-52” or “U1327-54”.

Is DTC “U1327-52” or “U1327-54” detected?

YES>>

  • “U1327–52”: Refer to DTC Description.

  • “U1327–54”: Refer to DTC Description.

NO>>

GO TO 2.

CHECK MAC DIAGNOSIS

With CONSULT

Perform “MAC Diagnosis” mode of “CHASSIS CONTROL” using CONSULT.

Is DTC "U2E65-57" detected with "U2140-57", "U2141-57", "U214F-57", "U2152-57", "U2165-57", "U2E52-57", and "U2E75-57" at the same time?

YES (all DTC codes are detected at the same time)>>

Replace the chassis control module. Refer to Removal and Installation.

NO (all DTC codes are not detected at the same time)>>

GO TO 3.

CHECK CAN COMMUNICATION SYSTEM

Check CAN communication system. Refer to Trouble Diagnosis Flow Chart.

>>

INSPECTION END

    U2e52-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2E52 87 CAN communication error (ADAS control unit) Diagnosis condition When ignition s...
    U2e75-57 Mac Comm Error (avm)
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2E75 57 CAN communication error (around view monitor control unit) Diagnosis condition ...

    Other materials:

    Chassis Can Communication 4 Circuit
    Diagnosis Procedure CHECK NETWORK DIAGNOSIS Check the "Network diagnosis" results from CONSULT to see that the diagnostic CAN communication circuit have no malfunction. Are the diagnostic CAN communication circuit normal? YES>> GO TO 2. NO>> Check and repair diagnostic CAN commu ...

    Dtc/circuit Diagnosis. Horn Function
    Component Function Check CHECK FUNCTION CONSULT Ignition switch OFF. Perform “Horn” in “Active test” mode of “IPDM E/R”. Check the horn operation. Test item Description Horn On Horn Sounds (for 20 ms.) Is the operation normal? YES>> Ins ...

    C106f-54 Steering Angle Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C106F 54 Steering angle sensor (Steering angle sensor) Diagnosis condition When ignition switch is ON. When the power supply voltage is normal. ...