Nissan Rogue (T33) 2021-Present Service Manual: U278c-88 Ethernet Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Electrical & Power Control :: Lan System / Can Gateway :: Dtc Diagnosis [8ch Can Gateway (8ch Can Gateway)] / U278c-88 Ethernet Circuit

DTC Description

DTC DETECTION LOGIC

With type B meter

DTC No. CONSULT screen terms DTC detected condition
U278C-88 Ethernet circuit Diagnosis condition When ignition switch is ON.
Signal (terminal) —
Threshold Lost ethernet communication with AV control unit
Diagnosis delay time 120 seconds or more

With type A meter

DTC No. CONSULT screen terms DTC detected condition
U278C-88 Ethernet circuit Diagnosis condition When ignition switch is ON.
Signal (terminal) —
Threshold Lost ethernet communication with TCU
Diagnosis delay time 120 seconds or more

POSSIBLE CAUSE

  • Ethernet harness

  • 8CH CAN gateway

  • AV control unit (With type B meter)

  • TCU (With type A meter)

FAIL-SAFE

8CH CAN gateway stops transmitting and receiving ethernet communication signals between ethernet communication circuit which cannot communicate.

Confirmation Procedure

With type B meter

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Ignition switch ON and wait at least 120 seconds or more.

  2. Select “Self Diagnostic Result” mode of “8ch CAN GATEWAY 2” using CONSULT.

  3. Check DTC.

Is DTC U278C–88 detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

With type A meter

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Ignition switch ON and wait at least 180 seconds or more.

  2. Select “Self Diagnostic Result” mode of “8ch CAN GATEWAY 3” using CONSULT.

  3. Check DTC.

Is DTC U278C–88 detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

With type B meter

CHECK CONNECTOR

  1. Ignition switch OFF.

  2. Check the ethernet harness connectors and terminals of 8CH CAN gateway and AV control unit for damage or looseness.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace the malfunction part, securely lock the harness connector.

PERFORM ALL DTC READING

  1. Ignition switch ON.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if any DTCs of ethernet (DTC “U2754-88”) are detected in “Self Diagnostic Result” of “MULTI AV”

Are any DTCs of ethernet detected?

YES>>

Replace the 8CH CAN gateway (Refer to Removal and Installation.), and GO TO 3.

NO>>

Replace the AV control unit. Refer to Removal and Installation.

PERFORM DTC CONFIRMATION PROCEDURE-1

  1. Erases all self-diagnosis results with CONSULT.

  2. Perform DTC confirmation procedure again. Refer to Confirmation Procedure.

Is DTC “U278C-88” detected as the current malfunction?

YES>>

Replace the AV control unit (Refer to Removal and Installation.), and GO TO 4.

NO>>

INSPECTION END

PERFORM DTC CONFIRMATION PROCEDURE-2

  1. Erases all self-diagnosis results with CONSULT.

  2. Perform DTC confirmation procedure again. Refer to Confirmation Procedure.

Is DTC “U278C-88” detected as the current malfunction?

YES>>

Replace the ethernet harness between 8CH CAN gateway and AV control unit.

NO>>

INSPECTION END

With type A meter

CHECK CONNECTOR

  1. Ignition switch OFF.

  2. Check the ethernet harness connectors and terminals of 8CH CAN gateway and TCU for damage or looseness.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace the malfunction part, securely lock the harness connector.

PERFORM ALL DTC READING

  1. Ignition switch ON.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if any DTCs of ethernet (DTC “U276D-88”) are detected in “Self Diagnostic Result” of “IVC”.

Are any DTCs of ethernet detected?

YES>>

Replace the 8CH CAN gateway (Refer to 8CH CAN GATEWAY: Removal and Installation.), and GO TO 3.

NO>>

Replace the TCU. Refer to TCU: Removal & Installation.

PERFORM DTC CONFIRMATION PROCEDURE-1

  1. Erases all self-diagnosis results with CONSULT.

  2. Perform DTC confirmation procedure again. Refer to Confirmation Procedure.

Is DTC “U278C-88” detected as the current malfunction?

YES>>

Replace the TCU (Refer to TCU: Removal & Installation.), and GO TO 4.

NO>>

INSPECTION END

PERFORM DTC CONFIRMATION PROCEDURE-2

  1. Erases all self-diagnosis results with CONSULT.

  2. Perform DTC confirmation procedure again. Refer to Confirmation Procedure.

Is DTC “U278C-88” detected as the current malfunction?

YES>>

Replace the ethernet harness between 8CH CAN gateway and TCU.

NO>>

INSPECTION END

    U2340-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detected condition U2340-87 CAN communication error (ECM) Diagnosis condition When ignition switch is ON. Si...
    U288c-88 Ethernet Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detected condition U288C-88 Ethernet circuit Diagnosis condition When ignition switch is ON. Signal (termina...

    Other materials:

    U2212 Can Comm Err (brake Unit)
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms DTC detection condition U2212 87 CAN communication error brake unit Diagnosis condition Ignition switch ON Signal (terminal) CAN communication signal Threshold ECM is not recieving CAN communication ...

    Intake Manifold
    Exploded View Electric throttle control actuator Electric throttle control actuator gasket Manifold absolute pressure (MAP) sensor O-ring Intake manifold support Intake manifold Intake manifold gasket         Comply with the assemb ...

    Precaution. Tow Truck Towing
    Tow Truck Towing WARNING: Never ride in a vehicle that is being towed. Never get under your Nissan Ariya vehicle after it has been lifted by a tow truck. CAUTION: All applicable state or Provincial (in Canada) laws and local laws regarding the towing operation must be obeyed. ...