Nissan Rogue (T33) 2021-Present Service Manual: U2541-83 Can Comm Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Cruise Control & Driver Assistance :: Driver Assistance System / Chassis Control :: Dtc/circuit Diagnosis / U2541-83 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
U2541 83 CAN communication error (TCM) Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold TCM in malfunctioning.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • CAN communication system

  • TCM

FAIL-SAFE

The following functions are suspended.

  • Automatic brake hold function

  • Intelligent trace control function (With Telematics System)

  • Active ride control function (With Telematics System)

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Ignition switch OFF to ON.

    CAUTION:

    Be sure to wait of 10 seconds after ignition switch OFF or ON.

  2. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U2541-83” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS

With CONSULT

  1. Erase self-diagnosis result for “CHASSIS CONTROL”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U2541-83” detected?

YES>>

GO TO 2.

NO>>

INSPECTION END

CHECK TCM SYSTEM (1)

With CONSULT

  1. Erase self-diagnosis result for “TRANSMISSION”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “TRANSMISSION”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 3.

CHECK TCM SYSTEM (2)

  1. Ignition switch OFF.

  2. Disconnect TCM harness connector.

  3. Check TCM harness connector terminals (CAN communication line) for damage or loose connection.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

ERASE SELF-DIAGNOSIS RESULT

With CONSULT

  1. Connect TCM harness connector.

  2. Erase self-diagnosis result for “CHASSIS CONTROL”.

  3. Ignition switch OFF and wait for 10 seconds or more.

>>

INSPECTION END

    U24a6-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U24A6 87 CAN communication error (power network separate relay) Diagnosis condition When...
    U2541-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2541 87 CAN communication error (TCM) Diagnosis condition When ignition switch is ON. S...

    Other materials:

    P2135 Tp Sensor
    DTC Description DTC DETECTION LOGICNOTE: If DTC P2135 is displayed with DTC P06B0, first perform the trouble diagnosis for DTC P06B0. Refer to DTC Description. DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2135 00 TP SENSOR-B1 (Throttle/Pedal ...

    U2e52-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2E52 87 CAN communication error (ADAS control unit) Diagnosis condition When ignition switch is ON. Signal (terminal) CAN communication signal Threshold Not receiving from ADAS c ...

    Cvt: Ge0f14a. Symptom Diagnosis
    Cvt Control System Symptom Table The diagnosis item number indicates the order of check. Start checking in the order from 1. Perform diagnoses of symptom table 1 before symptom table 2. Symptom Table 1 Diagnostic item Reference Symptom Shift Shock Slips/Will Not Engage Other ...