Nissan Rogue (T33) 2021-Present Service Manual: U2448-87 Can Comm Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Cruise Control & Driver Assistance :: Driver Assistance System / Chassis Control :: Dtc/circuit Diagnosis / U2448-87 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
U2448 87 CAN communication error [ABS actuator and electric unit (control unit)] Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold Not receiving from ABS actuator and electric unit (control unit).
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • CAN communication system

  • ABS actuator and electric unit (control unit)

FAIL-SAFE

The following functions are suspended.

  • Intelligent trace control function

  • Active ride control function

  • Automatic brake hold function

  • Drive mode selector function (Without Telematics System)

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Ignition switch OFF to ON.

    CAUTION:

    Be sure to wait of 10 seconds after ignition switch OFF or ON.

  2. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U2448-87” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS

With CONSULT

  1. Erase self-diagnosis result for “CHASSIS CONTROL”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U2448-87” detected?

YES>>

GO TO 2.

NO>>

INSPECTION END

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SYSTEM (1)

With CONSULT

  1. Erase self-diagnosis result for “ABS”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “ABS”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 3.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SYSTEM (2)

  1. Ignition switch OFF.

  2. Disconnect ABS actuator and electric unit (control unit) harness connector.

  3. Check ABS actuator and electric unit (control unit) harness connector terminals (CAN communication line) for damage or loose connection.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

ERASE SELF-DIAGNOSIS RESULT

With CONSULT

  1. Connect ABS actuator and electric unit (control unit) harness connector.

  2. Erase self-diagnosis result for “CHASSIS CONTROL”.

  3. Ignition switch OFF and wait for 10 seconds or more.

>>

INSPECTION END

    U2359-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2359 87 CAN communication error (steering unit) Diagnosis condition When ignition switc...
    U24a6-83 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U24A6 83 CAN communication error (power network separate relay) Diagnosis condition When...

    Other materials:

    Door Lock Function
    System Description SYSTEM DIAGRAMDoor lock function controls operation function of the following items. Door lock and unlock function (door request switch) Selective unlock function (door request switch) Reminder function (door request switch) Auto door lock function (door request ...

    Dtc/circuit Diagnosis. C18d6-09 Brake Power Supply Back up Unit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition C18D6 09 Backup power supply unit 1 Diagnosis condition When Ignition switch is ON. Signal (terminal) Brake power supply backup unit signal Threshold When a malfunction is de ...

    2wd. Preparation. Preparation
    Preparation Special Service Tool Tool number (TechMate No.) Tool name Description KV40104000 ( – ) Hub lock nut wrench a: 85 mm (3.35 in) b: 65 mm (2.56 in) Removing and Installing wheel hub lock nut. KV40107300 ( – ) Boot band crimping tool Installing bo ...