Nissan Rogue (T33) 2021-Present Service Manual: U215b-87 Can Comm Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Cruise Control & Driver Assistance :: Driver Assistance System / Chassis Control :: Dtc/circuit Diagnosis / U215b-87 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
U215B 87 CAN communication error (IPDM E/R) Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold Not receiving from IPDM E/R.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • CAN communication system

  • IPDM E/R

FAIL-SAFE

The following functions are suspended.

Automatic brake hold function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Ignition switch OFF to ON.

    CAUTION:

    Be sure to wait of 10 seconds after ignition switch OFF or ON.

  2. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U215B-87” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS

With CONSULT

  1. Erase self-diagnosis result for “CHASSIS CONTROL”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U215B-87” detected?

YES>>

GO TO 2.

NO>>

INSPECTION END

CHECK IPDM E/R SYSTEM (1)

With CONSULT

  1. Erase self-diagnosis result for “IPDM E/R”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “IPDM E/R”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 3.

CHECK IPDM E/R SYSTEM (2)

  1. Ignition switch OFF.

  2. Disconnect IPDM E/R harness connector.

  3. Check IPDM E/R harness connector terminals (CAN communication line) for damage or loose connection.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

ERASE SELF-DIAGNOSIS RESULT

With CONSULT

  1. Connect IPDM E/R harness connector.

  2. Erase self-diagnosis result for “CHASSIS CONTROL”.

  3. Ignition switch OFF and wait for 10 seconds or more.

>>

INSPECTION END

    U215b-83 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U215B 83 CAN communication error (IPDM E/R) Diagnosis condition When ignition switch is ...
    U2165-57 Mac Comm Error (sonar Control Unit)
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2165 57 CAN communication error (sonar control unit) Diagnosis condition — Signal (te...

    Other materials:

    Dtc/circuit Diagnosis. B1029-09 Front Seat Belt Pre-Tensioner Lh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B1029-09 Front seat belt pre-tensioner LH (Front seat belt pre-tensioner left hand) Diagnosis condition When ignition switch is ON. Signal (terminal) Front ...

    Dtc/circuit Diagnosis. B0038-11 Rear Side A/b Module Rh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B0038-11 REAR SIDE A/B MODULE RH (Second Row Right Side Airbag Deployment Control) Diagnosis condition When ignition switch is ON. Signal (terminal) Rear si ...

    B2231-16 Battery Voltage
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detected condition B2231-16 Battery voltage (Battery voltage) Diagnosis condition When ignition switch is ON. Signal (terminal) Battery power supply Threshold 8 V or le ...