Nissan Rogue (T33) 2021-Present Service Manual: U215b-83 Can Comm Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Cruise Control & Driver Assistance :: Driver Assistance System / Chassis Control :: Dtc/circuit Diagnosis / U215b-83 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
U215B 83 CAN communication error (IPDM E/R) Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold IPDM E/R in malfunctioning.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • CAN communication system

  • IPDM E/R

FAIL-SAFE

The following functions are suspended.

Automatic brake hold function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Ignition switch OFF to ON.

    CAUTION:

    Be sure to wait of 10 seconds after ignition switch OFF or ON.

  2. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U215B-83” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS

With CONSULT

  1. Erase self-diagnosis result for “CHASSIS CONTROL”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U215B-83” detected?

YES>>

GO TO 2.

NO>>

INSPECTION END

CHECK IPDM E/R SYSTEM (1)

With CONSULT

  1. Erase self-diagnosis result for “IPDM E/R”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “IPDM E/R”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 3.

CHECK IPDM E/R SYSTEM (2)

  1. Ignition switch OFF.

  2. Disconnect IPDM E/R harness connector.

  3. Check IPDM E/R harness connector terminals (CAN communication line) for damage or loose connection.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

ERASE SELF-DIAGNOSIS RESULT

With CONSULT

  1. Connect IPDM E/R harness connector.

  2. Erase self-diagnosis result for “CHASSIS CONTROL”.

  3. Ignition switch OFF and wait for 10 seconds or more.

>>

INSPECTION END

    U2154-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2154 87 CAN communication error (AV control unit) Diagnosis condition When ignition swi...
    U215b-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U215B 87 CAN communication error (IPDM E/R) Diagnosis condition When ignition switch is ...

    Other materials:

    B24a4-11 Intake Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B24A4-11 INTAKE SENSOR (Intake sensor) Diagnosis condition Ignition switch ON Signal (Terminal) Intake sensor signal Threshold The intake sensor rec ...

    U2648-87 Can Comm Circuit
    DTC Description CAN COMMUNICATIONCAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Ariya vehicle multiplex communication line with high data communication speed and excellent error detection ability. Modern Nissan Ariya vehicle is eq ...

    Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses
    Work Flow CUSTOMER INTERVIEWInterview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diagnostic Worksheet during the interview to document the facts and conditions when the noise occurs and any of customer's comments; Refer to Diagnostic Work ...