Nissan Rogue (T33) 2021-Present Service Manual: U10a0 Lost Communication (vcr)

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / U10a0 Lost Communication (vcr)

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
U10A0 00

Lost communication (Variable compression ratio)

[Lost communication (Variable compression ratio)] 		Diagnosis condition —
Signal (terminal) CAN communication signal
Threshold ECM cannot receive a communication signal sent from the VCR control module
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness and connectors (CAN communication line is open or shorted.)

  • ECM

  • VCR control module

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Check 1st trip DTC.

Is DTC U10A0 detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK VCR CONTROL MODULE POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect VCR control module harness connector.

  3. Check the voltage between VCR control module harness connector and ground.

    + − Voltage
    VCR control module
    Connector Terminal
    F108 5 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3

NO>>

GO TO 2

CHECK FUSE

Pull out 30A fuse (No.AA) from fuse and fusible link block.

Is the fuse blown (open)?

YES>>

Replace the fuse after repairing the applicable circuit.

NO>>

Perform trouble diagnosis for power supply.

CHECK CAN COMMUNICATION CIRCUIT

  1. Disconnect ECM harness connector.

  2. Disconnect VCR control module harness connector.

  3. Check the continuity between ECM harness connector and VCR control module harness connector.

    ECM VCR control module Continuity
    Connector Terminal Connector Terminal
    E21 131 F108 17 Existed
    132 16

  4. Check harness for short to ground.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

REPLACE VCR CONTROL MODULE

  1. Replace VCR control module.

  2. Perform DTC Confirmation Procedure again. Refer to DTC Description.

Is the DTC U10A0 displayed again?

YES>>

Replace VCR control module.

NO>>

INSPECTION END

    U1040 Eng Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition U1040 00 ENG COMM CIRCUIT (Engine communication circuit) Dia...
    U1327 Mac Key
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition U1327 52 MAC Key update (MAC Key update) Diagnosis condition —...

    Other materials:

    Service After Replacing or Removing Engine Parts
    Description X: Applicable Part name Service performed Required service Reference Replacement Removal   ECM X — Additional service when replacing ECM Work Procedure Fuel injector offset learning Work Procedure Turbocharger wastegate control solenoid valve d ...

    For Side and Rollover Collision
    When SRS is activated in a collision FOR SIDE AND ROLLOVER COLLISION: When SRS is activated in a collisionCAUTION: Due to varying models and option levels, not all parts listed in the chart below apply to all Nissan Ariya vehicles. WORK PROCEDURE Before performing any of the following steps, e ...

    Fuel Efficient Driving Tips
    Follow these Fuel Efficient Driving Tips to help maximize fuel economy in your Nissan Rogue. 1. Use smooth accelerator and brake input. Avoid rapid acceleration and sudden stops. Apply the accelerator and brakes smoothly. Maintain a consistent speed and coast when possible. 2. Maintain steady ...