Nissan Rogue manuals

Nissan Rogue Service Manual: Symptom diagnosis

EXTERIOR LIGHTING SYSTEM SYMPTOMS

Symptom Table

CAUTION: Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any DTC is detected.

Symptom Table

Symptom Table

NORMAL OPERATING CONDITION

Description

AUTO LIGHT SYSTEM

The headlamp may not be turned ON/OFF immediately after passing dark area or bright area (short tunnel, sky bridge, shadowed area, etc.) while using the auto light system. This is caused by for the control difference.

This is normal.

BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON

Description

Both side headlamps (HI) are not turned ON when setting to the lighting switch HI or PASS.

Diagnosis Procedure

1.COMBINATION SWITCH INSPECTION

Check combination switch. Refer to BCS-73, "Symptom Table" (with Intelligent Key system) or BCS-133, "Symptom Table" (without Intelligent Key system).

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace the malfunctioning part.

2.CHECK HEADLAMP (HI) REQUEST SIGNAL INPUT

CONSULT DATA MONITOR

  1.  Select “HEADLAMP (HI)”of IPDM E/R data monitor item.
  2.  With operating the lighting switch, check the monitor status.

Check headlamp (hi) request signal input

Is the inspection result normal? YES >> GO TO 3.

NO >> Replace BCM. Refer to BCS-75, "Removal and Installation" (with Intelligent Key system) or BCS- 135, "Removal and Installation" (without Intelligent Key system).

3.HEADLAMP (HI) CIRCUIT INSPECTION

Check headlamp (HI) circuit. Refer to EXL-246, "DTC Logic" (LH) or EXL-247, "DTC Logic" (RH).

Is the inspection result normal? YES >> Refer to GI-41, "Intermittent Incident".

NO >> Repair or replace the malfunctioning part.

BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON

Description

Both side headlamps (LO) are not turned ON in any condition.

Diagnosis Procedure

1.CHECK COMBINATION SWITCH

Check combination switch. Refer to BCS-73, "Symptom Table" (with Intelligent Key system) or BCS-133, "Symptom Table" ( without Intelligent Key system).

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace the malfunctioning part.

2.CHECK HEADLAMP (LO) REQUEST SIGNAL INPUT

CONSULT DATA MONITOR

  1. Select “HEADLAMP (LO)”of IPDM E/R data monitor item.
  2.  With operating the lighting switch, check the monitor status.

Check headlamp (lo) request signal input

Is the inspection result normal? YES >> GO TO 3.

NO >> Replace BCM. Refer to BCS-75, "Removal and Installation" (with Intelligent Key system) or BCS- 135, "Removal and Installation" (without Intelligent Key system).

3.HEADLAMP (LO) CIRCUIT INSPECTION

Check headlamp (LO) circuit. Refer to EXL-248, "DTC Logic" (LH) or EXL-249, "DTC Logic" (RH).

Is the inspection result normal? YES >> Refer to GI-41, "Intermittent Incident".

NO >> Repair or replace the malfunctioning part.

PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT TURNED ON

Description

The parking, license plate, side marker, tail lamps and each illumination are not turned ON in any condition.

Diagnosis Procedure

1.COMBINATION SWITCH INSPECTION

Check combination switch. Refer to BCS-73, "Symptom Table" (with Intelligent Key system) or BCS-133, "Symptom Table" (without Intelligent Key system).

Is the combination switch normal? YES >> GO TO 2.

NO >> Repair or replace the malfunctioning part.

2.CHECK TAIL LAMP REQUEST SIGNAL INPUT

CONSULT DATA MONITOR

  1.  Select “TAIL LAMP” of IPDM E/R data monitor item.
  2.  With operating the lighting switch, check the monitor status.

Check tail lamp request signal input

Is the inspection result normal? YES >> Replace IPDM E/R. Refer to PCS-35, "Removal and Installation".

NO >> Replace BCM. Refer to BCS-75, "Removal and Installation" (with Intelligent Key system) or BCS- 135, "Removal and Installation" (without Intelligent Key system).

BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON

Description

The front fog lamps are not turned ON in any condition.

Diagnosis Procedure

1.CHECK COMBINATION SWITCH

Check combination switch. Refer to BCS-73, "Symptom Table" (with Intelligent Key) or BCS-133, "Symptom Table" (without Intelligent Key).

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace the malfunctioning part.

2.CHECK FRONT FOG LAMP REQUEST SIGNAL INPUT

CONSULT DATA MONITOR

  1.  Select “FRONT FOG LAMP REQ” of IPDM E/R data monitor item.
  2.  With operating the front fog lamp switch, check the monitor status.

Check front fog lamp request signal input

Is the item status normal? YES >> Replace IPDM E/R. Refer to PCS-35, "Removal and Installation".

NO >> Replace BCM. Refer to BCS-75, "Removal and Installation" (with Intelligent Key) or BCS-135, "Removal and Installation" (without Intelligent Key).

DTC/circuit diagnosis
POWER SUPPLY AND GROUND CIRCUIT BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM) BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM) : Diagnosis Procedure Regarding Wiring Diagram infor ...

Periodic maintenance
HEADLAMP AIMING ADJUSTMENT Inspection PREPARATION BEFORE ADJUSTING Before performing aiming adjustment, check the following:  Make sure all tires are inflated to correct pressure.   ...

Other materials:

Wiring diagram
ENGINE START FUNCTION Wiring Diagram NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS Wiring Diagram VEHICLE SECURITY SYSTEM Wiring Diagram ...

Removal and installation
AV CONTROL UNIT Exploded View AV control unit bracket (LH) AV control unit AV control unit bracket (RH) Removal and Installation REMOVAL CAUTION:  Before disconnecting the AV control unit and battery terminals, turn the ignition switch OFF and wait at least 30 secon ...

Operating range
Operating range The Intelligent Key functions can only be used when the Intelligent Key is within the specified operating range from the request switch 1 . When the Intelligent Key battery is discharged or strong radio waves are present near the operating location, the Intelligent Key op ...

© 2014-2023 Copyright www.nirogue.com