Nissan Rogue (T33) 2021-Present Service Manual: P06dc Engine Oil Pressure Control Solenoid Valve

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P06dc Engine Oil Pressure Control Solenoid Valve

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P06DC 00

Engine oil pressure control

(Engine Oil Pressure Control Circuit High) 		Diagnosis condition Engine running from idle to 4000 rpm
Signal Engine oil pressure control solenoid valve signal
Threshold Signal voltage from the fuel rail pressure sensor remains at more than 3.1 V
Diagnosis delay time 5 seconds or more

POSSIBLE CAUSE

  • Harness or connectors (Engine oil pressure control solenoid valve circuit is shorted.)

  • Engine oil pressure control solenoid valve

FAIL-SAFE

Not applicable

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for at least 5 seconds.

  2. Check DTC.

Is DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ENGINE OIL PRESSURE CONTROL SOLENOID VALVE POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect engine oil pressure control solenoid valve harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between engine oil pressure control solenoid valve harness connector and ground.

    + − Voltage
    Engine oil pressure control solenoid valve
    Connector Terminal
    F88 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Perform the trouble diagnosis for power supply circuit.

CHECK ENGINE OIL PRESSURE CONTROL SOLENOID VALVE INPUT SIGNAL CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between engine oil pressure control solenoid valve harness connector and ECM harness connector.

    + − Continuity
    Engine oil pressure control solenoid valve ECM
    Connector Terminal Connector Terminal
    F88 2 F71 65 Existed

  4. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

CHECK ENGINE OIL PRESSURE CONTROL SOLENOID VALVE

Check the engine oil pressure control solenoid valve. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace engine oil pressure control solenoid valve. Refer to Exploded View.

    P06db Engine Oil Pressure Control Solenoid Valve
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P06DB 00 ENGINE OIL PRESSURE CONTROL (Engine oil pressure contro...
    P06e6 Internal Control Module
    DTC Description DESCRIPTIONECM supplies a voltage of 5 V to some of the sensors systematically divided into 3 groups, respectively. Accordingly, when a short circuit develops in...

    Other materials:

    Removal and Installation. Back Door
    Exploded View Roof seal Back door weather-strip Back door hinge LH Back door stay LH* Stud ball Back door bumper rubber upper Back door bumper rubber lower Back door striker TORX bolt Back door panel Back door stay RH* Back door hinge RH ...

    Meter Speaker Signal Circuit
    Diagnosis Procedure CHECK METER SPEAKER CIRCUIT FOR OPEN Ignition switch OFF. Disconnect combination meter harness connector and meter speaker harness connector. Check the continuity between combination meter harness connector and meter speaker harness connector. Combination meter ...

    Admission Valve
    Component Inspection CHECK ADMISSION VALVE-1 With CONSULT Turn ignition switch ON (engine stopped). Perform “ADM/V motor target angle” in “Active Test” mode of “ENGINE” using CONSULT. Operate “Up” or “Down”, set “ADM/V Target Angle” to 0 deg, and check value ...