Nissan Rogue (T33) 2021-Present Service Manual: P06da Engine Oil Pressure Control Solenoid Valve

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P06da Engine Oil Pressure Control Solenoid Valve

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P06DA 00

ENGINE OIL PRESSURE CONTROL

(Engine oil pressure control circuit/open) 		Diagnosis condition —
Signal (terminal) —
Threshold

ECM detects the following status continuously for 5 seconds or more:

A voltage signal from engine oil pressure control solenoid valve is around 0V or more and less than normal operating voltage
Diagnosis delay time 5 consecutive seconds

POSSIBLE CAUSE

  • Harness or connectors

    (Engine oil pressure control solenoid valve circuit is open or shorted.)

  • Engine oil pressure control solenoid valve

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Maintain engine speed at 4,500 rpm or more for at least 5 seconds.

  3. Check DTC.

Is DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ENGINE OIL PRESSURE CONTROL SOLENOID VALVE POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect engine oil pressure control solenoid valve harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between engine oil pressure control solenoid valve harness connector and ground.

    + − Voltage
    Engine oil pressure control solenoid valve
    Connector Terminal
    F88 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Perform the trouble diagnosis for power supply circuit.

CHECK ENGINE OIL PRESSURE CONTROL SOLENOID VALVE INPUT SIGNAL CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between engine oil pressure control solenoid valve harness connector and ECM harness connector.

    + − Continuity
    Engine oil pressure control solenoid valve ECM
    Connector Terminal Connector Terminal
    F88 2 F71 65 Existed

  4. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

CHECK ENGINE OIL PRESSURE CONTROL SOLENOID VALVE

Check the engine oil pressure control solenoid valve. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace engine oil pressure control solenoid valve. Refer to Exploded View.

    P06b3 Sensor Power Supply 2
    DTC Description DESCRIPTIONECM supplies a voltage of 5 V to some of the sensors systematically divided into 3 groups, respectively. Accordingly, when a short circuit develops in...
    P06db Engine Oil Pressure Control Solenoid Valve
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P06DB 00 ENGINE OIL PRESSURE CONTROL (Engine oil pressure contro...

    Other materials:

    Window washer fluid
    Type A (if so equipped) Type B (if so equipped) For Type A systems on the Nissan Rogue, check the fluid level directly in the washer reservoir and refill when the level is low. For Type B systems, plug the center hole A of the cap/tube assembly with your finger, remove the tube, and chec ...

    P0261 Fuel Injector (cylinder 1)
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0261 00 CYL1 INJECTOR (Cylinder 1 Injector A Circuit Low) Diagnosis condition — Signal (terminal) — Threshold Direct injector driver unit ...

    Wl Chg Branch Line Circuit
    Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the following terminals and connectors for damage, bend and loose connection (unit side and connector side). Wireless charger unit Harness connec ...