Nissan Rogue (T33) 2021-Present Service Manual: P0315 Ckp Sensor (pos)

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P0315 Ckp Sensor (pos)

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P0315 00

Crankshaft position

(Crankshaft Position System Variation Not Learned) 		Diagnosis condition Engine run and fuel shut off
Signal (terminal) —
Threshold Learning value of signal plate variation is abnormal or not learned.
Diagnosis delay time —

POSSIBLE CAUSE

  • Signal plate

  • Crankshaft position sensor

  • Harness or connectors (Crankshaft position sensor circuit is open or shorted.)

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P0315 is displayed with DTC P0335, first perform the trouble diagnosis for DTC P0335.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Description.

NO>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine and warm it up to normal operating temperature.

  2. Drive Nissan Ariya vehicle at 80 km/h, with selecting suitable gear.

    NOTE:

    Always keep safe driving to the first priority.

  3. Release accelerator pedal completely to decelerate the Nissan Ariya vehicle.

    NOTE:

    Always keep safe driving to the first priority.

  4. Repeat the step 2 and 3 until the integrated deceleration time to be 30 seconds.

  5. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P0315 is displayed with DTC P0335, first perform the trouble diagnosis for DTC P0335.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Description.

NO>>

GO TO 2.

CHECK GEAR TOOTH

Visually check for chipping signal plate gear tooth.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace the signal plate. Refer to Exploded View.

    P0300 Misfire
    DTC Description DTC DETECTION LOGICWhen a misfire occurs, engine speed will fluctuate. If the engine speed fluctuates enough to cause the crankshaft position (CKP) sensor signal...
    P0326 Knock Sensor 1 Bank 1
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detected condition P0326 00 KNOCK SENSOR 1 B1 (Knock/Combustion Vibration Sensor 1 C...

    Other materials:

    U0074-00 Av Communication
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition U0074-00 Control module comm Bus B Off (Control module communication bus B off) Diagnosis condition When ignition switch is ON Signal (terminal) AV communic ...

    Tilt/telescopic steering
    Basic information WARNING Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident. Do not adjust the steering wheel any closer to you than is necessary for proper steering operation and comfort. The driver's air bag inflates with great ...

    Intelligent Key
    CONSULT Function (BCM - INTELLIGENT KEY) DATA MONITORNOTE: The following table includes information (items) inapplicable to this Nissan Ariya vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items. Monitor Item Condition Stop/start switch [On/Off] ...