Nissan Rogue (T33) 2021-Present Service Manual: P0265 Fuel Injector (cylinder 2)

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P0265 Fuel Injector (cylinder 2)

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P0265 00

CYL2 INJECTOR

(Cylinder 2 Injector "A" Circuit High) 		Diagnosis condition —
Signal (terminal) —
Threshold

  • Direct injector driver unit is malfunctioning.

  • ECM detects direct fuel injector No. 2 circuit is shorted.
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors

    • Direct fuel injector circuit is shorted

  • Battery power supply

  • ECM (direct injector driver unit)

  • direct fuel injector

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Traveling control mode Accelerator angle variation control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction.

NOTE:

ECM does not control the accelerator pedal releasing speed.
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.
Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited.

When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Ignition switch OFF and wait at least 10 seconds.

  2. Ignition switch ON.

  3. Ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

  • Before performing the following procedure, confirm that battery voltage is between 12 - 15 V at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for at least 20 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DIRECT FUEL INJECTOR

Check direct fuel injector. Refer to Component Function Check.

Is inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

  4. Check 1st trip DTC.

Is the DTC P0265 displayed again?

YES>>

Replace ECM. Refer to ECM : Removal & Installation.

NO>>

INSPECTION END

    P0264 Fuel Injector (cylinder 2)
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0264 00 CYL2 INJECTOR (Cylinder 2 Injector "A" Circuit Low) Dia...
    P0267 Fuel Injector (cylinder 3)
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0267 00 CYL3 INJECTOR (Cylinder 3 Injector "A" Circuit Low) Dia...

    Other materials:

    B2721-11 Center Sensor [rl]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B2721-11 CENTER SENSOR [RL] (Center sensor [RL]) Diagnosis condition When ignition switch is ON Signal (terminal) Rear sonar sensor signal LH inner Threshold ...

    U2e52-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2E52 87 CAN communication error (ADAS control unit) Diagnosis condition When ignition switch is ON. Signal (terminal) CAN communication signal Threshold Not receiving from ADAS c ...

    Dtc/circuit Diagnosis. Horn Function
    Component Function Check CHECK FUNCTION CONSULT Ignition switch OFF. Perform “Horn” in “Active test” mode of “IPDM E/R”. Check the horn operation. Test item Description Horn On Horn Sounds (for 20 ms.) Is the operation normal? YES>> Ins ...