Nissan Rogue (T33) 2021-Present Service Manual: P0264 Fuel Injector (cylinder 2)

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P0264 Fuel Injector (cylinder 2)

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P0264 00

CYL2 INJECTOR

(Cylinder 2 Injector "A" Circuit Low) 		Diagnosis condition —
Signal (terminal) —
Threshold Direct injector driver unit is malfunctioning.
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors

    • direct fuel injector circuit is shorted

  • Battery power supply

  • ECM (direct injector driver unit)

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Traveling control mode Accelerator angle variation control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction.

NOTE:

ECM does not control the accelerator pedal releasing speed.
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.
Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited.

When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Ignition switch OFF and wait at least 10 seconds.

  2. Ignition switch ON.

  3. Ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

  • Before performing the following procedure, confirm that battery voltage is between 12 - 15 V at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for at least 20 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DIRECT FUEL INJECTOR

Check direct fuel injector. Refer to Component Inspection.

Is inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

  4. Check 1st trip DTC.

Is the DTC P0264 displayed again?

YES>>

Replace ECM. Refer to ECM : Removal & Installation.

NO>>

INSPECTION END

    P0262 Fuel Injector (cylinder 1)
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0262 00 CYL1 INJECTOR (Cylinder 1 Injector A Circuit High) Diag...
    P0265 Fuel Injector (cylinder 2)
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0265 00 CYL2 INJECTOR (Cylinder 2 Injector "A" Circuit High) Di...

    Other materials:

    Tcm
    Reference Value CONSULT DATA MONITOR STANDARD VALUE In CONSULT, electric shift timing or lock-up timing, i.e. operation timing of each solenoid valve, is displayed. Therefore, if there is an obvious difference between the shift timing estimated from a shift shock (or engine speed variation ...

    C0513 Wheel Speed Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition C0513 00 Right rear wheel speed sensor (Right Rear Wheel Speed Sensor Range/Performance) Diagnosis condition Ignition switch ON Battery voltage: 11 V ...

    C107c-53 Not Configuration
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C107C 53 Not configuration (Not configuration) Diagnosis condition When ignition switch is ON. When the power supply voltage is normal. Signa ...