Nissan Rogue (T33) 2021-Present Service Manual: P0090 Frp System

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P0090 Frp System

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P0090 00

FUEL PUMP

(Fuel Pressure Regulator "A" Control Circuit/Open) 		Diagnosis condition Engine running at idle
Signal (terminal) High pressure fuel pump signal
Threshold ECM detects High pressure fuel pump circuit is open
Diagnosis delay time 5 seconds

POSSIBLE CAUSE

  • Harness or connectors (The high pressure fuel pump circuit is open.)

  • High pressure fuel pump

FAIL-SAFE

Engine Control System

Not applicable

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited.

When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Turn ignition switch ON and wait at least 10 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Go to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK HIGH PRESSURE FUEL PUMP CIRCUIT

  1. Turn ignition switch ON.

  2. Disconnect ECM harness connector and high pressure fuel pump harness connector.

  3. Check the continuity between ECM harness connector and high pressure fuel pump harness connector.

    ECM High pressure fuel pump Continuity
    Connector Terminal Connector Terminal
    F72 7 F82 1 Existed
    2 2

  4. Also check harness for short to power and short to ground.

Is inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace the error-detected parts.

CHECK HIGH PRESSURE FUEL PUMP

Check high pressure fuel pump. Refer to Component Inspection.

Is inspection result normal?

YES>>

INSPECTION END

NO>>

Replace error-detected parts.

    P0088 Frp Control System
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0088 00 HIGH FUEL PRES (Fuel rail/system pressure - too high) D...
    P0096 Iat Sensor 2
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0096 00 IAT SENSOR 2 B1 [Intake air temperature sensor 2 circui...

    Other materials:

    Type B. Precaution. Precautions
    Precautions Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and ...

    Towing your vehicle
    Basic information When towing your vehicle, always follow local towing laws and regulations. Using incorrect equipment or improper towing procedures can damage your vehicle. Professional service operators typically know the proper towing methods. To prevent accidental damage, NISSAN recommends ha ...

    Removal and Installation. 12v Battery Current Sensor
    Exploded View : 12V battery current sensor : Harness connector : N·m (kg-m, in-lb) Removal and Installation REMOVALDisconnect the 12V battery current sensor connector . Remove negative cable mounting nut , and then remove the negative cable . Loosen 12V battery cu ...