Nissan Rogue (T33) 2021-Present Service Manual: P0079 Evt Control Solenoid Valve

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P0079 Evt Control Solenoid Valve

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P0079 00

Exhaust valve control solenoid

(Exhaust Valve Control Solenoid Circuit Low Bank 1) 		Diagnosis condition Engine running at idle
Signal (terminal) Exhaust valve timing control solenoid valve signal
Threshold An improper voltage is sent to the ECM through exhaust valve timing control solenoid valve
Diagnosis delay time 1 second or more

POSSIBLE CAUSE

  • Harness or connectors (Exhaust valve timing control solenoid valve circuit is open or shorted.)

  • Exhaust valve timing control solenoid valve

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited.

When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for 10 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P0079 is displayed with DTC P0090 and P1197, first perform the trouble diagnosis for DTC P0090 and P1197.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable.

  • DTC P0090: Refer to DTC Description.

  • DTC P1197: Refer to DTC Description.

NO>>

GO TO 2.

BLEED THE FUEL LINE

  1. Start the engine, and let the engine run at idle at least for 10 minutes.

  2. Perform DTC confirmation procedure of DTC P0079.

Is 1st trip DTC detected?

YES>>

GO TO 3.

NO>>

GO TO 7.

CHECK LOW FUEL PRESSURE

Check low fuel pressure. Refer to Work Procedure.

Is inspection result normal?

YES>>

GO TO 4.

NO>>

Check low fuel pressure system. Refer to Diagnosis Procedure.

CHECK LOW PRESSURE FUEL LINE FOR INTERNAL LEAKAGE

  1. Turn ignition switch OFF.

  2. Turn ignition switch ON.

  3. Check the following value 30 minutes after turning the ignition switch ON.

    Low fuel pressure : 206 kPa (2.1 bar, 2.2 kgf/cm2, 30 psi) or more

Is inspection result normal?

YES>>

GO TO 5.

NO>>

Replace “fuel level sensor unit and fuel pump”. Refer to Removal and Installation.

CHECK HIGH PRESSURE FUEL PUMP

Check high pressure fuel pump. Refer to Component Inspection.

Is inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace the error-detected parts.

CHECK HIGH PRESSURE FUEL PUMP LIFTER

Check high pressure fuel pump lifter. Refer to Removal and Installation.

Does the lifter top surface have scratches and/or dents?

YES>>

Replace the error-detected parts.

NO>>

INSPECTION END

CHECK LOW PRESSURE FUEL LINE FOR INTERNAL LEAKAGE

  1. Turn ignition switch OFF.

  2. Connect fuel pressure gauge. Refer to Work Procedure.

  3. Turn ignition switch ON.

  4. Check the following value 30 minutes after turning the ignition switch ON.

    Low fuel pressure : 206 kPa (2.1 bar, 2.2 kgf/cm2, 30 psi) or more

Is inspection result normal?

YES>>

INSPECTION END

NO>>

Replace “fuel level sensor unit and fuel pump”. Refer to Removal and Installation.

    P0078 Evt Control Solenoid Valve
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0078 00 EX V/T ACT/CIRC-B1 (Exhaust valve control solenoid circ...
    P0080 Evt Control Solenoid Valve
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0080 00 Exhaust valve control solenoid (Exhaust Valve Control S...

    Other materials:

    Repair Information. Preparation
    Repairing Material Foam Repair During factory body assembly, foam insulators are installed in certain body panels and locations around the Nissan Ariya vehicle. Use the following procedure(s) to replace any factory-installed foam insulators.URETHANE FOAM APPLICATIONSUse commercially availabl ...

    Dtc/circuit Diagnosis. B242a-98 Closure Motor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B242A-98 Closure motor (Closure motor) Diagnosis condition When back door closure function operate Signal (terminal) — Threshold When thermal prot ...

    Steering Switch Signal B Circuit
    Component Function Check CHECK COMBINATION METER INPUT SIGNAL CONSULT Ignition switch ON. Select “Steering switch input” in “Data monitor” mode of “M&A”. Check that the function operates normally according to the following conditions: Condition Value CONTRO ...