Nissan Rogue (T33) 2021-Present Service Manual: Optical Sensor Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Controls :: Exterior Lighting System / Led Headlamp :: Dtc/circuit Diagnosis / Optical Sensor Circuit

Component Function Check

CHECK OPTICAL SENSOR SIGNAL

  1. Ignition switch ON.

  2. Turn lighting switch AUTO.

  3. With the optical sensor illuminating, check the exterior lamps status.

    Condition Exterior lamp status
    Optical sensor When illuminating Turns OFF
    When shutting off light Turns ON

Is the inspection result normal?

YES>>

Optical sensor circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK OPTICAL SENSOR POWER SUPPLY

  1. Ignition switch ON.

  2. Turn lighting switch AUTO.

  3. Check voltage between optical sensor harness connector and ground.

    + -

    Voltage

    (Approx.)
    Optical sensor
    Connector Terminal
    M13 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 4.

CHECK OPTICAL SENSOR GROUND

  1. Ignition switch OFF.

  2. Disconnect optical sensor connector

  3. Check continuity between optical sensor harness connector and ground.

    + - Continuity
    Optical sensor
    Connector Terminal
    M13 3 Ground Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 6.

CHECK OPTICAL SENSOR SIGNAL

  1. Connect optical sensor connector.

  2. Ignition switch ON.

  3. Check voltage between optical sensor harness connector and ground.

    + -

    Voltage

    (Approx.)
    Optical sensor
    Connector Terminal
    M13 2 Ground 0.1 - 4.4 V

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

GO TO 8.

CHECK OPTICAL SENSOR POWER SUPPLY CIRCUIT (OPEN)

  1. Ignition switch OFF.

  2. Disconnect optical sensor connector and BCM connector.

  3. Check continuity between optical sensor harness connector and BCM harness connector.

    With type A meter
    Optical sensor BCM Continuity
    Connector Terminal Connector Terminal
    M13 1 M58 48 Yes
    With type B meter
    Optical sensor BCM Continuity
    Connector Terminal Connector Terminal
    M13 1 M18 28 Yes

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace harness.

CHECK OPTICAL SENSOR POWER SUPPLY CIRCUIT (SHORT)

Check continuity between optical sensor harness connector and ground.

Optical sensor — Continuity
Connector Terminal
M13 1 Ground No

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK OPTICAL SENSOR GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect optical sensor connector and BCM connector.

  3. Check continuity between optical sensor harness connector and BCM harness connector.

    With type A meter
    Optical sensor BCM Continuity
    Connector Terminal Connector Terminal
    M13 3 M58 42 Yes
    With type B meter
    Optical sensor BCM Continuity
    Connector Terminal Connector Terminal
    M13 3 M18 29 Yes

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK OPTICAL SENSOR SIGNAL CIRCUIT (OPEN)

  1. Ignition switch OFF.

  2. Disconnect optical sensor connector and BCM connector.

  3. Check continuity between optical sensor harness connector and BCM harness connector.

    With type A meter
    Optical sensor BCM Continuity
    Connector Terminal Connector Terminal
    M13 2 M58 47 Yes
    With type B meter
    Optical sensor BCM Continuity
    Connector Terminal Connector Terminal
    M13 2 M18 8 Yes

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK OPTICAL SENSOR SIGNAL CIRCUIT (SHORT)

Check continuity between optical sensor harness connector and ground.

Optical sensor — Continuity
Connector Terminal
M13 2 Ground No

Is the inspection result normal?

YES>>

Replace optical sensor. Refer to Removal and Installation.

NO>>

Repair or replace harness.

    Turn Signal Lamp Circuit
    Component Function Check CHECK TURN SIGNAL LAMP OPERATION CONSULT Ignition switch ON. Select “Flasher” in “Active test” mode of “BCM”. With operating the test item, ...
    Hazard Switch Circuit
    Component Function Check CHECK HAZARD SWITCH SIGNAL CONSULT Ignition switch ON. Select “Hazard switch” in “Data monitor” mode “BCM [FLASHER]”. With operating the haz...

    Other materials:

    Dtc/circuit Diagnosis. B0028-1a Side A/b Module Rh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B0028-1A SIDE A/B MODULE RH (Right Side Airbag Deployment Control) Diagnosis condition When ignition switch is ON. Signal (terminal) Front side air bag modu ...

    Dtc/circuit Diagnosis. C161b-86 Abs System
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C161B 86 ABS system (Anti-lock braking system ) Diagnosis condition When ignition switch is ON. Signal (terminal) CAN communication signal Threshold ...

    Dtc/circuit Diagnosis. B0073-09 Pre-Ten Rear Lh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B0073-09 PRE-TEN REAR LH (Second Row Left Seat Belt Pretensioner Deployment Control) Diagnosis condition When ignition switch is ON. Signal (terminal) Rear ...