Nissan Rogue (T33) 2021-Present Service Manual: Main Line Between Ccm and Brake Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Electrical & Power Control :: Lan System / Can :: Dtc/circuit Diagnosis / Main Line Between Ccm and Brake Circuit

Diagnosis Procedure

CHECK CONNECTOR

  1. Ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the following terminals and connectors for damage, bend and loose connection (connector side and harness side).

    • Harness connector M36

    • Harness connector B21

    • Harness connector B150

    • Harness connector E150

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the following harness connectors.

    • Chassis control module

    • Harness connectors M36 and B21

  2. Check the continuity between the chassis control module harness connector and the harness connector.

    Chassis control module harness connector Harness connector Continuity
    Connector No. Terminal No. Connector No. Terminal No.
    M32 24 M36 58G Existed
    7 67G Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the main line between the chassis control module and the harness connector M36.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the harness connector B150 and E150.

  2. Check the continuity between the harness connector terminals.

    Harness connector Continuity
    Connector No. Terminal No. Connector No. Terminal No.
    B21 58G B150 1 Existed
    67G 2 Existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair the main line between the harness connector B21 and B150.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the connector of electrically-driven intelligent brake unit.

  2. Check the continuity between the harness connector and the electrically-driven intelligent brake unit harness connector.

    Harness connector Electrically-driven intelligent brake unit Continuity
    Connector No. Terminal No. Connector No. Terminal No.
    E150 1 E61 25 Existed
    2 16 Existed

Is the inspection result normal?

YES>>

Present error: Check CAN system type decision again.

YES>>

Past error: Error was detected in the main line between the chassis control module and the electrically-driven intelligent brake unit.

NO>>

Repair the main line between the harness connector E150 and the electrically-driven intelligent brake unit.

    Main Line Between Pnsr and Ccm Circuit
    Diagnosis Procedure CHECK CONNECTOR Ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the following terminals and connectors for damage, bend a...
    Main Line Between Ccm and 4wd Circuit
    Diagnosis Procedure CHECK CONNECTOR Ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the following terminals and connectors for damage, bend a...

    Other materials:

    C106e-54 Steering Angle Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C106E 54 Steering angle sensor (Steering angle sensor) Diagnosis condition When ignition switch is ON. When the power supply voltage is normal. ...

    Steering Switch Signal B Circuit
    Component Function Check CHECK COMBINATION METER INPUT SIGNAL CONSULT Ignition switch ON. Select “Steering switch input” in “Data monitor” mode of “M&A”. Check that the function operates normally according to the following conditions: Condition Value CONTRO ...

    Automatic air conditioner (models without rear control)
    Models with heated steering wheel Models without heated steering wheel Basic information Temperature control dial (driver's side) AUTO button Display screen SYNC button Temperature control dial (passenger's side) ON·OFF button Air recirculation button Fan speed buttons Air flow ...