Nissan Rogue (T33) 2021-Present Service Manual: Its Can Communication 6 Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Electrical & Power Control :: Lan System / Can :: Dtc/circuit Diagnosis / Its Can Communication 6 Circuit

Diagnosis Procedure

CHECK CAN DIAGNOSIS

Check the CAN diagnosis results from CONSULT to see that the ITS CAN communication 1 circuit and ITS CAN communication 4 circuit have no malfunction.

Are the ITS CAN communication 1 circuit and ITS CAN communication 4 circuit normal?

YES>>

GO TO 2.

NO>>

Check and repair ITS CAN communication 1 circuit and/or ITS CAN communication 4 circuit.

CONNECTOR INSPECTION

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect all the control unit connectors on ITS CAN communication 6 circuit.

  4. Check the terminals and connectors for damage, bend and loose connection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

Check the continuity between the around view monitor control unit harness connector and sonar control unit harness connector.

Around view monitor control unit harness connector Sonar control unit harness connector Continuity
Connector No. Terminal No. Connector No. Terminal No.
B75 21 B49 28 Existed
5 26 Existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Check the harness and repair or replace the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the around view monitor control unit harness connector terminals.

Around view monitor control unit harness connector Continuity
Connector No. Terminal No.
B75 21 5 Not existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Check the harness and repair or replace the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the around view monitor control unit and the ground.

Around view monitor control unit harness connector Ground Continuity
Connector No. Terminal No.
B75 21 Not existed
5 Not existed

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Check the harness and repair or replace (if shield line is short) the root cause.

CHECK AROUND VIEW MONITOR CONTROL UNIT AND SONAR CONTROL UNIT TERMINATION CIRCUIT

  1. Remove the around view monitor control unit and the sonar control unit.

  2. Check the resistance between the around view monitor control unit terminals.

    Around view monitor control unit Resistance (Ω)
    Terminal No.
    21 5 Approx. 108 – 132

  3. Check the resistance between the sonar control unit terminals.

    Sonar control unit Resistance (Ω)
    Terminal No.
    28 26 Approx. 108 – 132

Is the measurement value within the specification?

YES>>

GO TO 7.

NO>>

Replace the around view monitor control unit and/or the sonar control unit.

CHECK SYMPTOM

Connect all the connectors. Check if the symptoms described in the “Symptom (Results from interview with customer)” are reproduced.

Inspection result

Reproduced>>

GO TO 8.

Non-reproduced>>

Start the diagnosis again. Follow the trouble diagnosis procedure when past error is detected.

CHECK UNIT REPRODUCTION

Perform the reproduction test as per the following procedure for each unit.

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Disconnect one of the unit connectors of ITS CAN communication 6 circuit.

    NOTE:

    Around view monitor control unit and sonar control unit have a termination circuits. Check other units first.

  4. Connect the battery cable to the negative terminal. Check if the symptoms described in the “Symptom (Results from interview with customer)” are reproduced.

    NOTE:

    Although unit-related error symptoms occur, do not confuse them with other symptoms.

Inspection result

Reproduced>>

Connect the connector. Check other units as per the above procedure.

Non-reproduced>>

Replace the unit whose connector was disconnected.

    Its Can Communication 5 Circuit
    Diagnosis Procedure CHECK CAN DIAGNOSIS Check the "Network Diagnosis" results from CONSULT to see that the ITS CAN communication 1 circuit, ITS CAN communication 4 circuit and d...
    Chassis Can Communication 1 Circuit
    Diagnosis Procedure CHECK CAN DIAGNOSIS Check the CAN diagnosis results from CONSULT to see that the chassis CAN communication 4 circuit have no malfunction. Are the chassis CAN...

    Other materials:

    Basic information
    WARNING Do not leave children, pets, or adults who require supervision alone inside the Nissan Rogue. Interior temperatures on hot days can rise quickly and lead to serious or fatal injuries. Secure all cargo with straps or ropes inside the Nissan Rogue to prevent items from shifting or sliding d ...

    P0500 Vss
    DTC Description DESCRIPTIONECM receives vehicle speed signals from two different paths via CAN communication line: One is from the ABS actuator and electric unit (control unit) via the combination unit and the other is from TCM.DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagno ...

    Corrosion protection
    Most common factors contributing to vehicle corrosion Moisture-retaining dirt and debris build-up inside body cavities or seams. Paint or coating damage caused by gravel, small stones or minor collisions. Environmental factors influencing corrosion rate Moisture Sand, dirt and water accumulat ...