Nissan Rogue (T33) 2021-Present Service Manual: For Rear Collision

Nissan Rogue (T33) 2021-Present Service Manual / Restraints :: Srs Air Bag / Basic Inspection :: Collision Diagnosis / For Rear Collision

For rear collision

FOR REAR COLLISION: When SRS is not activated in a collision

CAUTION:

Due to varying models and option levels, not all parts listed in the chart below apply to all Nissan Ariya vehicles.

WORK PROCEDURE

Before performing any of the following steps, ensure that all vehicle body and structural repairs have been completed.

Check the SRS components using the table below.

Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc).

Perform self-diagnosis using CONSULT or air bag warning lamp. Refer to DTCIndex. for details.

Ensure entire SRS operates properly.

After the work is completed, check that no malfunction is detected by air bag warning lamp. Refer to Warning Lamp/Indicator Lamp.

SRS INSPECTION (FOR REAR COLLISION)

Part Inspection
Driver air bag module

If the driver air bag has not been activated:

  1. Remove driver air bag module. Check harness cover and connectors for damage, terminals for deformities, and harness for binding.

  2. Install driver air bag module into the steering wheel to check fit and alignment with the wheel.

  3. If no damage is found, reinstall with new fasteners.

  4. If damaged - REPLACE. Install driver air bag modules with new fasteners.
Driver knee air bag module

If the driver knee air bag has not been activated:

  1. Remove driver knee air bag module. Check harness cover and connectors for damage, terminals for deformities, and harness for binding.

  2. Install driver knee air bag module into the instrument panel to check fit with the instrument panel.

  3. If no damage is found, reinstall with new fasteners.

  4. If damaged - REPLACE. Install driver knee air bag modules with new fasteners.
Front passenger air bag module

If the front passenger air bag has not been activated:

  1. Remove front passenger air bag module. Check harness cover and connectors for damage, terminals for deformities, and harness for binding.

  2. Install front passenger air bag module into the instrument panel to check fit with the instrument panel.

  3. If no damage is found, reinstall with new fasteners.

  4. If damaged - REPLACE. Install front passenger air bag modules with new fasteners.
Front passenger knee air bag module

If the front passenger knee air bag has not been activated:

  1. Remove front passenger knee air bag module. Check harness cover and connectors for damage, terminals for deformities, and harness for binding.

  2. Install front passenger knee air bag module into the instrument panel to check fit with the instrument panel.

  3. If no damage is found, reinstall with new fasteners.

  4. If damaged - REPLACE. Install front passenger knee air bag modules with new fasteners.
Crash zone sensor

If the front air bags or seat belt pre-tensioners have not been activated:

  1. Remove the crash zone sensor. Check harness connectors for damage, terminals for deformities, and harness for binding.

  2. Check for visible signs of damage (dents, cracks, deformation) of the crash zone sensor and bracket.

  3. Install the crash zone sensor to check fit.

  4. If no damage is found, reinstall with new fasteners.

  5. If damaged - REPLACE the crash zone sensor and bracket with new fasteners.

Seat belt pre-tensioner assemblies

(All applicable locations: buckle, retractor, lap outer)

If the pre-tensioners have not been activated:

  1. Remove seat belt pre-tensioners.

    Check harness cover and connectors for damage, terminals for deformities, and harness for binding.

  2. Check belts for damage and anchors for loose mounting.

  3. Check retractor for smooth operation.

  4. Check seat belt adjuster for damage.

  5. Check for deformities of the center pillar inner.

  6. If the center pillar inner has no damage, REPLACE the seat belt pre-tensioner assembly.

  7. If no damage is found, reinstall seat belt pre-tensioner assembly with new fasteners.

  8. If damaged - REPLACE. Install the seat belt pre-tensioner assembly with new fasteners.
Diagnosis sensor unit

If none of the SRS components have been activated:

  1. Check case for dents, cracks or deformities.

  2. Check connectors for damage, and terminals for deformities.

  3. If no damage is found, reinstall with new fasteners.

  4. If damaged - REPLACE. Install diagnosis sensor unit with new fasteners.
Steering wheel

  1. Visually check steering wheel for deformities.

  2. Check harness (built into steering wheel) and connectors for damage, and terminals for deformities.

  3. Install driver air bag module into the steering wheel to check fit and alignment with the wheel.

  4. Check steering wheel for excessive free play.

  5. If no damage is found, reinstall.

  6. If damaged - REPLACE.
Spiral cable

If the driver front air bag has not deployed:

  1. Visually check spiral cable and combination switch for damage.

  2. Check connectors and protective tape for damage.

  3. Check steering wheel for noise, binding or heavy operation.

  4. If no damage is found, reinstall.

  5. If damaged - REPLACE.
Occupant classification system (Passenger seat)

  1. Remove passenger seat assembly.

  2. Check control unit case for dents, cracks of deformities.

  3. Check connectors for damage and terminals for deformities.

  4. Check seat frame and cushion pan for dents or deformities.

  5. If no damage is found, reinstall seat with new fasteners.

  6. If damaged - REPLACE seat cushion assembly with new fasteners.

  7. Perform zero point reset function after front passenger seat is installed in the Nissan Ariya vehicle and all bolts are tightened to specification. Refer to Work Procedure.
Harness and connectors

  1. Check connectors for poor connection, damage, and terminals for deformities.

  2. Check harness for binding, chafing, cuts, or deformities.

  3. If no damage is found, reinstall the harness and connectors.

  4. If damaged - REPLACE the damaged harness. Do not attempt to repair, splice or modify any SRS harness.
Instrument panel assembly

If the passenger front air bag has not deployed:

  1. Visually check instrument panel for damage.

  2. If no damage is found, reinstall the instrument panel assembly.

  3. If damaged - REPLACE the instrument panel assembly.
    For Side and Rollover Collision
    When SRS is activated in a collision FOR SIDE AND ROLLOVER COLLISION: When SRS is activated in a collisionCAUTION: Due to varying models and option levels, not all parts listed ...
    Removal and Installation. Driver Air Bag Module
    Exploded View 1. Steering wheel 2. Driver air bag module     Removal and Installation WARNING: Always observe the following items for preventing accidental activation....

    Other materials:

    Diagnosis System (tcm)
    Diagnosis Description 1 Trip Detection Diagnosis and 2 Trip Detection Diagnosis NOTE: “Start the engine and turn OFF the ignition switch after warm-up.” This is defined as 1 trip. 1 TRIP DETECTION DIAGNOSISWhen initial malfunction is detected, TCM memorizes DTC. In these diagnoses, some ...

    Awd. Service Data and Specifications (sds). Service Data and Specifications (sds)
    Service Data and Specifications (sds) Wheel Bearing Axial end play 0.05 mm (0.002 in) or less Drive Shaft Item   Standard Grease quantity Wheel side 49 – 69 g (1.73 – 2.43 oz) Final drive side 78 – 98 g (2.76 – 3.45 oz) Boots installed length* Wheel ...

    Fuel Efficient Driving Tips
    Follow these Fuel Efficient Driving Tips to help maximize fuel economy in your Nissan Rogue. 1. Use smooth accelerator and brake input. Avoid rapid acceleration and sudden stops. Apply the accelerator and brakes smoothly. Maintain a consistent speed and coast when possible. 2. Maintain steady ...