Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: U224f-87 Can Comm Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake System / Dtc/circuit Diagnosis :: U224f-87 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
U224F 87 CAN communication error (BCM) 1 Diagnosis condition When Ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When not receiving from BCM.
Diagnosis delay time 2 seconds or more
2 Diagnosis condition When Ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When not transmitting to BCM.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • BCM

  • CAN communication line

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always Ignition switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

CAUTION:

Never operate the Nissan Ariya vehicle.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF to ON without depressing the brake pedal.

  2. Ignition switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  4. Ignition switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Ignition switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  8. Ignition switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “U224F-87" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

Refer to Trouble Diagnosis Flow Chart.

    Dtc/circuit Diagnosis. U2248-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2248 87 CAN communication error brake control unit 1 Diagnosis condition When Ignition ...
    Dtc/circuit Diagnosis. U2252-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2252 87 CAN communication error advanced driver assistant systems control unit 1 Diagno...

    Other materials:

    Front Wheel Hub and Knuckle
    Exploded View Steering knuckle Splash guard Hub bolt Wheel hub and bearing assembly Disc rotor Wheel hub lock nut : Comply with the installation procedure when tightening. Refer to Removal and Installation. : N·m (kg-m, ft-lb) : Always replace aft ...

    P0106 Manifold Absolute Pressure Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0106 00 ABSL PRES SEN/CIRC (Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Range/Performance) Diagnosis condition — Signal (terminal) ...

    Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses
    Work Flow CUSTOMER INTERVIEWInterview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diagnostic Worksheet during the interview to document the facts and conditions when the noise occurs and any of customer's comments; Refer to Diagnostic Work ...