Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: U1ca7-02 Front Seat Heater Lh Communication
DTC Description
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen items (Trouble diagnosis content) | DTC detection condition | |
|---|---|---|---|
| U1CA7-02 |
FRONT SEAT HEATER LH COMMUNICATION (Front seat heater LH communication) |
Diagnosis condition | Engine running |
| Signal (terminal) | LIN (heated seat) signal (terminal #45) | ||
| Threshold | A/C amp. is not transmitting or receiving LIN communication with front seat heater LH | ||
| Diagnosis delay time | 2 seconds or more | ||
POSSIBLE CAUSE
-
Fuse
-
Harness or connectors (front seat heater LH circuit is open or short to ground)
-
Seat cushion heater LH
-
A/C amp.
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
PERFORM DTC CONFIRMATION PROCEDURE
CONSULT
-
Start the engine.
-
Select “Self diagnosis result” mode of “HVAC”.
Is DTC detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: Inspection End.
DTC Diagnosis Procedure
CHECK FUSE
-
Ignition switch OFF.
-
Check that the following fuse is not blown (open):
Unit Location Fuse No. Capacity Ignition switch power supply Fuse block (J/B) 67 30A
Is the fuse blown (open)?
YES>>Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).
NO>>GO TO 2.
CHECK FRONT SEAT HEATER LH POWER SUPPLY VOLTAGE
-
Disconnect front seat heater LH connector.
-
Start the engine.
-
Check voltage between front seat heater LH harness connector and ground.
+ - Voltage
(Approx.)Front seat heater LH Connector Terminal B204 1 Ground Battery voltage
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair the harness or connector.
CHECK FRONT SEAT HEATER LH GROUND CIRCUIT (OPEN)
-
Ignition switch OFF.
-
Check continuity between front seat heater LH harness connector and ground.
Front seat heater LH — Continuity Connector Terminal B204 2 Ground Yes
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair the harness or connector.
CHECK FRONT SEAT HEATER LH LIN SIGNAL
-
Ignition switch ON.
-
Confirm output waveform between front seat heater LH harness connector and ground with oscilloscope.
+ – Output waveform Front seat heater LH Connector Terminal B204 3 Ground 
Is the inspection result normal?
YES>>Replace seat cushion heater LH. Refer to Disassembly and Assembly.
NO>>GO TO 5.
CHECK FRONT SEAT HEATER LH LIN SIGNAL CIRCUIT (OPEN)
-
Ignition switch OFF.
-
Disconnect A/C amp. connector.
-
Check continuity between front seat heater LH harness connector and A/C amp. harness connector.
Front seat heater LH A/C amp. Continuity Connector Terminal Connector Terminal B204 3 M55 45 Yes
Is the inspection result normal?
YES>>GO TO 6.
NO>>Repair the harness or connector.
CHECK FRONT SEAT HEATER LH LIN SIGNAL CIRCUIT (SHORT TO GROUND)
-
Disconnect following connectors:
-
Front seat heater RH
-
Rear seat heater LH
-
Rear seat heater RH
-
-
Check continuity between front seat heater LH harness connector and ground.
Front seat heater LH — Continuity Connector Terminal B204 3 Ground No
Is the inspection result normal?
YES>>Replace A/C amp. Refer to Removal and Installation.
NO>>Repair the harness or connector.
Other materials:
Dtc/circuit Diagnosis. B0028-1a Side A/b Module Rh
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen items
(Trouble diagnosis content) DTC Detection Condition
B0028-1A
SIDE A/B MODULE RH
(Right Side Airbag Deployment Control)
Diagnosis condition
When ignition switch is ON.
Signal (terminal)
Front side air bag modu ...
Cvt: Ge0f14a. Symptom Diagnosis
Cvt Control System
Symptom Table
The diagnosis item number indicates the order of check. Start checking in the order from 1.
Perform diagnoses of symptom table 1 before symptom table 2.
Symptom Table 1 Diagnostic item Reference Symptom
Shift Shock Slips/Will Not Engage Other
...
U224a-87 Can Comm Err (awd/4wd)
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen terms
(Trouble diagnosis content) DTC detection condition
U224A
87
CAN comm err (AWD/4WD)
[Controller area network communication error (AWD/4WD control unit)]
1
Diagnosis condition
When ignition switch is ON.
...
