Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Rear Seat Heater Switch Lh

Nissan Rogue (T33) 2021-Present Service Manual / Body Interior :: Seat / Dtc/circuit Diagnosis :: Rear Seat Heater Switch Lh

Component Function Check

CAUTION:

Before performing the diagnosis, check that the following are normal:

  • Rear seat heater LH

CHECK REAR SEAT HEATER SWITCH LH FUNCTION

  1. Start the engine.

  2. Check that rear seat heater switch LH indicator (Low, Mid, High) turns ON when operating rear seat heater switch LH.

Is the inspection result normal?

YES>>

Rear seat heater switch LH function is OK.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK REAR SEAT HEATER SWITCH LH POWER SUPPLY VOLTAGE

  1. Ignition switch OFF.

  2. Disconnect rear seat heater switch LH connector.

  3. Ignition switch ON.

  4. Check voltage between rear seat heater switch LH harness connector and ground.

    + —

    Voltage

    (Approx.)
    Rear seat heater switch LH
    Connector Terminal
    M203 5 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 2.

CHECK REAR SEAT HEATER SWITCH LH SIGNAL CIRCUIT (OPEN)

  1. Ignition switch OFF.

  2. Disconnect A/C switch assembly connector.

  3. Check continuity between rear seat heater switch LH harness connector and A/C switch assembly harness connector.

    Rear seat heater switch LH A/C switch assembly Continuity
    Connector Terminal Connector Terminal
    M203 5 M84 8 Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the harness or connector.

CHECK REAR SEAT HEATER SWITCH LH SIGNAL CIRCUIT (SHORT TO GROUND)

Check continuity between rear seat heater switch LH harness connector and ground.

Rear seat heater switch LH — Continuity
Connector Terminal
M203 5 Ground No

Is the inspection result normal?

YES>>

Replace A/C switch assembly. Refer to Removal and Installation.

NO>>

Repair the harness or connector.

CHECK REAR SEAT HEATER SWITCH LH GROUND CIRCUIT (OPEN)

  1. Ignition switch OFF.

  2. Check continuity between rear seat heater switch LH harness connector and ground.

    Rear seat heater switch LH — Continuity
    Connector Terminal
    M203 7 Ground Yes

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair the harness or connector.

CHECK REAR SEAT HEATER SWITCH LH

Check rear seat heater switch LH. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Replace rear seat heater switch LH. Refer to Removal and Installation.

CHECK FUSE

Check that the following fuse is not blown (open):

Unit Location Fuse No. Capacity
Ignition switch power supply Fuse block (J/B) 65 5A

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 7.

CHECK REAR SEAT HEATER SWITCH LH INDICATOR POWER SUPPLY VOLTAGE

  1. Start the engine.

  2. Check voltage between rear seat heater switch LH harness connector and ground.

    + —

    Voltage

    (Approx.)
    Rear seat heater switch LH
    Connector Terminal
    M203 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair the harness or connector.

CHECK REAR SEAT HEATER SWITCH LH INDICATOR SIGNAL VOLTAGE

  1. Ignition switch OFF.

  2. Connect rear seat heater switch LH connector.

  3. Start the engine.

  4. Check voltage between rear seat heater switch LH harness connector and ground.

    + —

    Voltage

    (Approx.)
    Rear seat heater switch LH
    Connector Terminal
    M203 2 Ground Battery voltage
    3
    4

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Replace the rear seat heater switch LH. Refer to Removal and Installation.

CHECK REAR SEAT HEATER SWITCH LH INDICATOR SIGNAL CIRCUIT (OPEN)

  1. Ignition switch OFF.

  2. Disconnect rear seat heater switch LH connector and A/C switch assembly connector.

  3. Check continuity between rear seat heater switch LH harness connector and A/C switch assembly harness connector.

    Rear seat heater switch LH A/C switch assembly Continuity
    Connector Terminal Connector Terminal
    M203 2 M84 9 Yes
    3 10
    4 11

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair the harness or connector.

REPLACE A/C SWITCH ASSEMBLY

  1. Replace A/C switch assembly. Refer to Removal and Installation.

  2. Reconnect all connectors.

  3. Start the engine.

  4. Check that rear seat heater switch LH indicator (Low, Mid, High) turns ON when operating rear seat heater switch LH.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace A/C amp. Refer to Removal and Installation.

Component Inspection

CHECK REAR SEAT HEATER SWITCH LH

  1. Ignition switch OFF.

  2. Disconnect rear seat heater switch LH connector.

  3. Check continuity between rear seat heater switch LH terminals.

    Rear seat heater switch LH Condition Continuity
    Terminal
    5 7 Pressed Yes
    Not pressed No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace rear seat heater switch LH. Refer to Removal and Installation.

    Dtc/circuit Diagnosis. Front Seat Heater Lh
    Component Function Check CHECK FRONT SEAT HEATER LH FUNCTION Start the engine. Check that seat cushion and seat back of front seat LH warms when operating front seat heater swit...
    Symptom Diagnosis. Heated Seat System
    Symptom Table Symptom Inspection item Front seat heater LH is inoperative. Front seat heater LH circuit Seat cushion heater LH Front seat back heater LH A/C amp. Refer to Compon...

    Other materials:

    Sièges, ceintures de sécurité et systèmes de retenue supplémentaires (SRS)
    Dans le Nissan Rogue, la sécurité des occupants repose sur l’association des ceintures, des appuie-tête et des dispositifs SRS (airbags et capteurs). Reportez-vous toujours aux avertissements du manuel avant toute intervention sur un composant SRS. Airbags avant : protection frontale du ...

    Cvt: Ge0f14a. Symptom Diagnosis
    Cvt Control System Symptom Table The diagnosis item number indicates the order of check. Start checking in the order from 1. Perform diagnoses of symptom table 1 before symptom table 2. Symptom Table 1 Diagnostic item Reference Symptom Shift Shock Slips/Will Not Engage Other ...

    Diagnosis System (hvac)
    CONSULT Function CONSULT performs the following functions via CAN communication with A/C amp. Diagnosis mode Function Self diagnosis result Display non-network DTC which A/C amp. memorizes ECU identification The A/C amp. part number is displayed Active Test The signals used t ...