Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Front Seat Heater Lh
Component Function Check
CHECK FRONT SEAT HEATER LH FUNCTION
-
Start the engine.
-
Check that seat cushion and seat back of front seat LH warms when operating front seat heater switch LH.
Is the inspection result normal?
YES>>Front seat heater LH function is OK.
NO>>Refer to Diagnosis Procedure.
Diagnosis Procedure
CHECK FUSE
-
Ignition switch OFF.
-
Check that the following fuse is not blown (open):
Unit Location Fuse No. Capacity Ignition switch power supply Fuse block (J/B) 67 30A
Is the fuse blown (open)?
YES>>Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).
NO>>GO TO 2.
CHECK FRONT SEAT HEATER LH POWER SUPPLY VOLTAGE
-
Disconnect front seat heater LH connector.
-
Start the engine.
-
Check voltage between front seat heater LH harness connector and ground.
(+) (-) Voltage
(Approx.)Front seat heater LH Connector Terminal B204 1 Ground Battery voltage
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair the harness or connector.
CHECK FRONT SEAT HEATER LH GROUND CIRCUIT (OPEN)
-
Ignition switch OFF.
-
Check continuity between front seat heater LH harness connector and ground.
Front seat heater LH – Continuity Connector Terminal B204 2 Ground Yes 4
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair the harness or connector.
CHECK FRONT SEAT HEATER LH LIN SIGNAL
-
Ignition switch ON.
-
Confirm output waveform between front seat heater LH harness connector and ground with oscilloscope.
(+) (–) Output waveform Front seat heater LH Connector Terminal B204 3 Ground 
Is the inspection result normal?
YES>>GO TO 7.
NO>>GO TO 5.
CHECK FRONT SEAT HEATER LH LIN SIGNAL CIRCUIT (OPEN)
-
Ignition switch OFF.
-
Disconnect A/C amp. connector.
-
Check continuity between front seat heater LH harness connector and A/C amp. harness connector.
Front seat heater LH A/C amp. Continuity Connector Terminal Connector Terminal B204 3 M55 45 Yes
Is the inspection result normal?
YES>>GO TO 6.
NO>>Repair the harness or connector.
CHECK FRONT SEAT HEATER LH LIN SIGNAL CIRCUIT (SHORT TO GROUND)
-
Disconnect following connectors:
-
Front seat heater RH
-
Rear seat heater LH
-
Rear seat heater RH
-
-
Check continuity between front seat heater LH harness connector and ground.
Front seat heater LH — Continuity Connector Terminal B204 3 Ground No
Is the inspection result normal?
YES>>Replace A/C amp. Refer to Removal and Installation.
NO>>Repair the harness or connector.
CHECK FRONT SEAT BACK HEATER LH CIRCUIT (OPEN)
-
Ignition switch OFF.
-
Check continuity between front seat back heater LH harness connector and front seat heater LH harness connector.
Front seat back heater LH Front seat heater LH Continuity Connector Terminal Connector Terminal B209 2 B220 1 Yes
Is the inspection result normal?
YES>>GO TO 8.
NO>>Replace seat cushion heater LH. Refer to Disassembly and Assembly.
CHECK FRONT SEAT BACK HEATER LH GROUND CIRCUIT (OPEN)
-
Disconnect front seat back heater LH connector.
-
Check continuity between front seat back heater LH harness connector and front seat heater LH harness connector.
Front seat back heater LH Front seat heater LH Continuity Connector Terminal Connector Terminal B209 1 B220 4 Yes
Is the inspection result normal?
YES>>Replace front seat back heater LH. Refer to Disassembly and Assembly.
NO>>Replace seat cushion heater LH. Refer to Disassembly and Assembly.
Other materials:
Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses
Work Flow
CUSTOMER INTERVIEWInterview
the customer if possible, to determine the conditions that exist when
the noise occurs. Use the Diagnostic Worksheet during the interview to
document the facts and conditions when the noise occurs and any of
customer's comments; Refer to Diagnostic Work ...
Removal and Installation. Rear Wheel House Protector
Exploded View
Rear wheel house protector
Spring nut
: Nissan Ariya Vehicle front
Removal and Installation
REMOVALRemove rear fillet molding rear. Refer to Removal and Installation.
Remove rear parting seal. Refer to Removal and Installation.
Remove rear defle ...
Push-Button Ignition Switch Circuit
Component Function Check
CHECK FUNCTION
CONSULT
Ignition switch ON.
Select “Push switch” in “Data monitor” mode of “INTELLIGENT KEY”.
Check the push-button ignition switch signal under the following conditions:
Monitor item Condition Status
Push switch
Pus ...
