Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Hood Switch

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Security Control System / Dtc/circuit Diagnosis :: Hood Switch

Component Function Check

CHECK FUNCTION

CONSULT

  1. Select “Hood switch (CAN)” or “Hood switch” in “Data onitor” mode of “IPDM E/R”.

  2. Check “Hood switch (CAN)” or “Hood switch” indication under the following condition:

Monitor item Condition Indication
Hood switch (CAN) Close the hood Close
Open the hood Open
Transmits invalid CAN signal NG
Hood switch Close the hood Close
Open the hood Open

Is the indication normal?

YES>>

Hood switch is OK.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK HOOD SWITCH SIGNAL CIRCUIT 1

  1. Ignition switch OFF.

  2. Disconnect hood switch connector.

  3. Check voltage between hood switch harness connector and ground.

(+) (–)

Voltage

(Approx.)
Hood switch
Connector Terminal
E100 2 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK HOOD SWITCH SIGNAL CIRCUIT 2

  1. Disconnect IPDM E/R connector.

  2. Check continuity between IPDM E/R harness connector and hood switch harness connector.

    IPDM E/R Hood switch Continuity
    Connector Terminal Connector Terminal
    E217 52 E100 2 Yes

  3. Check continuity between IPDM E/R harness connector and ground.

    IPDM E/R — Continuity
    Connector Terminal
    E217 52 Ground No

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK HOOD SWITCH GROUND CIRCUIT

Check continuity between hood switch harness connector and ground.

Hood switch — Continuity
Connector Terminal
E100 1 Ground Yes

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness.

CHECK HOOD SWITCH

Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace hood lock assembly. Refer to Removal and Installation.

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

>>

Inspection End.

Component Inspection

CHECK HOOD SWITCH

  1. Ignition switch OFF.

  2. Disconnect hood switch connector.

  3. Check continuity between hood switch terminals.

    Hood switch Condition Continuity
    Terminal
    1 2 Hood lock Unlock condition No
    Lock condition Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace hood lock assembly. Refer to Removal and Installation.

    Dtc/circuit Diagnosis. B2556-73 Push-Btn Ign Sw
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detecting condition B2556-73 PUSH-BTN IGN SW (Push-button ignition switch) Diagn...
    Dtc/circuit Diagnosis. Horn Function
    Component Function Check CHECK FUNCTION CONSULT Ignition switch OFF. Perform “Horn” in “Active test” mode of “IPDM E/R”. Check the horn operation. Test item Descript...

    Other materials:

    Basic Inspection. Additional Service When Replacing Driver Seat Control Unit
    Description Each function is reset to the following condition when the driver seat control unit is replaced. For details, refer to Work Procedure. Function Condition Procedure Memory (Seat, mirror) Erased Perform memory storing Log-in*1 Erased Perform log-in storing Inte ...

    Fonctionnement du système RAB
    Exemple Témoin d'avertissement du système RAB (sur l'écran d'informations du véhicule) Témoin d'avertissement de désactivation du système RAB (sur le tableau de bord) Commandes au volant (côté gauche) Écran d'informations du véhicule Centre d'affichage (si le véhicule e ...

    Charge Air Cooler
    Exploded View Charge air cooler Charge air cooler Bracket 1 Turbocharger boost sensor (with intake air temperature sensor 2) O-ring Electronic throttle control actuator gasket Charge air cooler Bracket 2 Air inlet hose         To r ...