Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: C18eb-01 Brake Power Supply Back up Unit

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake System / Dtc/circuit Diagnosis :: C18eb-01 Brake Power Supply Back up Unit

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
C18EB 01 Backup power supply unit 1 Diagnosis condition When Ignition switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When brake power supply backup unit power supply voltage is 7.5 V or less.
Diagnosis delay time 1 second or less
2 Diagnosis condition When Ignition switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When brake power supply backup unit power supply voltage is 9.0 V or less (when brake operation is not request).
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Brake power supply backup unit

  • Brake power supply backup unit power supply system

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always Ignition switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

CAUTION:

Never operate the Nissan Ariya vehicle.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF to ON without depressing the brake pedal.

  2. Ignition switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  4. Ignition switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Ignition switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  8. Ignition switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18EB-01" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Ignition switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Ignition switch OFF to ON without depressing the brake pedal.

  3. Ignition switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  5. Ignition switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Ignition switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  9. Ignition switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EB-01" detected?

YES>>

GO TO 3.

NO>>

Inspection End.

CHECK CONNECTOR TERMINALS

  1. Ignition switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect Electrically-driven Intelligent Brake Unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect brake power supply backup unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

CONSULT

  1. Connect Electrically-driven Intelligent Brake Unit harness connector.

  2. Connect brake power supply backup unit harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Ignition switch OFF to ON without depressing the brake pedal.

  5. Ignition switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  7. Ignition switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Ignition switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  11. Ignition switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EB-01" detected?

YES>>

GO TO 5.

NO>>

Inspection End.

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect brake power supply backup unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Ignition switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  5. Disconnect 12V battery cable from negative terminal.

  6. Check the Electrically-driven Intelligent Brake Unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

CONSULT

  1. Ignition switch OFF to ON without depressing the brake pedal.

  2. Ignition switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  4. Ignition switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Ignition switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  8. Ignition switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EB-01" detected?

YES>>

GO TO 7.

NO>>

Inspection End.

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (1)

  1. Ignition switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect Electrically-driven Intelligent Brake Unit harness connector.

  5. Disconnect brake power supply backup unit harness connector.

  6. Check the continuity between Electrically-driven Intelligent Brake Unit and brake power supply backup unit.

    Electrically-driven Intelligent Brake Unit Brake power supply backup unit Continuity
    Connector Terminal Connector Terminal

    B63*1

    B642    		 17 B94 1 Existed
    4 Not existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.1

    *2: With ProPILOT Assist 2.1

  7. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit — Continuity
    Connector Terminal
    B94 1 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness or connector. GO TO 8.

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (2)

  1. Ignition switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  3. Disconnect 12V battery cable from negative terminal.

  4. Check the 30A fusible link (#62).

  5. Check the continuity and for short circuit between harness connector terminal 6 of brake power supply backup unit and 30A fusible link (#62).

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Perform trouble diagnosis for 12V battery power supply.

CHECK BRAKE POWER SUPPLY BACKUP UNIT COMMUNICATION CIRCUIT

  1. Check the continuity between Electrically-driven Intelligent Brake Unit and brake power supply backup unit.

    Electrically-driven Intelligent Brake Unit Brake power supply backup unit Continuity
    Connector Terminal Connector Terminal

    B63*1

    B642

    4*1

    5*2    		 B94 1 Not existed
    4 Not existed
    5 Existed
    6 Not existed

    *1: Without ProPILOT Assist 2.1

    *2: With ProPILOT Assist 2.1

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit — Continuity
    Connector Terminal
    B94 5 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 10.

CHECK BRAKE POWER SUPPLY BACKUP UNIT WAKE UP CIRCUIT

  1. Check the continuity between Electrically-driven Intelligent Brake Unit and brake power supply backup unit.

    Electrically-driven Intelligent Brake Unit Brake power supply backup unit Continuity
    Connector Terminal Connector Terminal

    B63*1

    B642    		 24 B94 1 Not existed
    4 Existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.1

    *2: With ProPILOT Assist 2.1

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit — Continuity
    Connector Terminal
    B94 4 Ground Not existed

Is the inspection result normal?

YES>>

Replace the brake power supply backup unit. Refer to Removal & Installation.

NO>>

Repair / replace harness or connector.

    Dtc/circuit Diagnosis. C18ea-01 Abs Actuator and Electric Unit (control Unit) System
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition C18EA 01 VDC system Diagnosis condition When Ignition switch is ON. Signal (terminal) CA...
    Dtc/circuit Diagnosis. C18ec-01 Stroke Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition C18EC 01 Stroke sensor Diagnosis condition When Ignition switch is ON. Signal (terminal)...

    Other materials:

    Dtc/circuit Diagnosis. P161d-00 Immobilizer
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detecting condition P161D-00 IMMOBILIZER (Immobilizer) Diagnosis condition Ignition switch ON Signal (terminal) — Threshold When Intelligent Key unit detects an immob ...

    Front Wheel Hub and Knuckle
    Exploded View Steering knuckle Splash guard Hub bolt Wheel hub and bearing assembly Disc rotor Wheel hub lock nut : Comply with the installation procedure when tightening. Refer to Removal and Installation. : N·m (kg-m, ft-lb) : Always replace aft ...

    C107c-53 Not Configuration
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C107C 53 Not configuration (Not configuration) Diagnosis condition When ignition switch is ON. When the power supply voltage is normal. Signa ...