Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: C1743-21 Tire Pressure Sensor No Data Rr

Nissan Rogue (T33) 2021-Present Service Manual / Suspension :: Road Wheels & Tires / Dtc/circuit Diagnosis :: C1743-21 Tire Pressure Sensor No Data Rr

DTC Description

NOTE:

The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information.

  • Activate and display TPMS sensor IDs

  • Display tire pressure reported by the TPMS sensor

  • Read TPMS DTCs

  • Register TPMS sensor IDs

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C1743-21

Tire pressure sensor no data RR

(Tire pressure sensor no data rear right) 		Diagnosis condition Drive at a speed of 25 MPH (40 km/h) or more reaches 10 minutes in total.
Signal (terminal) Tire pressure sensor signal.
Threshold Tire pressure data signal from the rear right tire pressure sensor cannot be detected.
Diagnosis delay time 10 minutes or more.

POSSIBLE CAUSE

  • Driving in area with radio interference

  • Rear right tire pressure sensor ID registration incomplete

  • Rear right tire pressure sensor

  • Harness or connectors

  • BCM

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

TIRE PRESSURE SENSOR ID REGISTRATION

CONSULT

Perform tire pressure sensor ID registration. Refer to Description.

Can the tire pressure sensor ID registration be completed?

>>

GO TO 2.

PERFORM DTC CONFIRMATION

CONSULT

  1. Drive the Nissan Ariya vehicle at 25 MPH (40 km/h) or more until reaching 10 minutes in total.

    NOTE:

    Avoid driving in areas with radio interference.

  2. Stop the Nissan Ariya vehicle.

  3. Perform “Self diagnosis result” mode of “BCM”.

Is DTC “C1743-21” detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

NOTE:

The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information.

  • Activate and display TPMS sensor IDs

  • Display tire pressure reported by the TPMS sensor

  • Read TPMS DTCs

  • Register TPMS sensor IDs

CHECK TIRE PRESSURE SIGNAL

CONSULT

  1. Select "Air pressure-rear right" in "Data monitor" mode of "BCM [AIR PRESSURE MONITOR]".

  2. Check that the rear right tire pressures match the standard value. Refer to Reference Value.

    NOTE:

    BCM holds last tire pressure values during 17 minutes after ignition switch turns OFF.

Are all tire pressures displayed 0 kPa (psi)?

YES>>

GO TO 2.

NO>>

GO TO 3.

CHECK BCM POWER SUPPLY CIRCUIT

Check BCM power supply circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness or connectors.

TIRE PRESSURE SENSOR ID REGISTRATION

Perform tire pressure sensor ID registration. Refer to Description.

Can the tire pressure sensor ID registration be completed?

YES>>

GO TO 4.

NO>>

Replace applicable rear right tire pressure sensor. Refer to Removal & Installation.

RECHECK TIRE PRESSURE SIGNAL

CONSULT

  1. Drive the Nissan Ariya vehicle at 25 MPH (40 km/h) or more until reaching 10 minutes in total.

    NOTE:

    Avoid driving in areas with radio interference.

  2. Stop the Nissan Ariya vehicle.

  3. Select "Air pressure-rear right" in "Data monitor" mode of "BCM [AIR PRESSURE MONITOR]".

  4. Check that the rear right tire pressures match the standard value. Refer to Reference Value.

Is the inspection result normal?

YES>>

After erasing DTC record, Inspection End.

NO>>

Replace BCM. Refer to Removal and Installation.

    Dtc/circuit Diagnosis. C1742-21 Tire Pressure Sensor No Data Fr
    DTC Description NOTE: The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information....
    Dtc/circuit Diagnosis. C1744-21 Tire Pressure Sensor No Data Rl
    DTC Description NOTE: The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information....

    Other materials:

    P14a7 Charge Air Cooler Cooling Electric Water Pump
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P14A7 Charge air cooler cooling electric W/P (Charge air cooler cooling electric water pump) Diagnosis condition Engine running at idle Warm-up conditio ...

    U2e52-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2E52 87 CAN communication error (ADAS control unit) Diagnosis condition When ignition switch is ON. Signal (terminal) CAN communication signal Threshold Not receiving from ADAS c ...

    Electric Wastegate Control Actuator
    Component Inspection INSPECTION START Do you have CONSULT? Do you have CONSULT? YES>> GO TO 2. NO>> GO TO 3. CHECK ELECTRIC WASTEGATE CONTROL ACTUATOR With CONSULT Turn ignition switch ON and engine stopped. On the CONSULT screen, select “ENGINE”>>“ACTIVE ...